Current Science

Open Access Open Access  Restricted Access Subscription Access

Partial Factors for Shear Capacity Assessment of In-Service RC T-Girder Bridges


Affiliations
1 CSIR-Structural Engineering Research Centre, CSIR Campus, Taramani, Chennai 600 113, India
 

As the infrastructure age, their assessment to carry the loads they are subjected to becomes increasingly important. Also, assessment is needed as part of a regular monitoring programme. Before carrying out a rigorous probabilistic analysis for assessment, it is often required to make a preliminary assessment using simplified procedures, such as that developed using semi-probabilistic approach, in which partial factors are used. In this article an attempt has been made to evolve a framework to determine the partial factors for safety assessment of the in-service T-girder bridges in India against the limit state of shear. Limit state of shear is considered because it is one of the important ultimate limit states for bridge girder that results in brittle failure. The partial factors are derived using first order reliability method. In order to suggest a simple method for safety assessment, statistical properties of modelling error associated with the simplified equation of shear capacity estimation are estimated using test data of 185 beams reported in the literature. To demonstrate the usefulness of the framework developed, an attempt has been made to determine partial factors for assessment for a typical T-girder bridge designed according to the relevant Indian codes. The loading considered corresponds to actual traffic loads on a typical Chennai flyover. The study reported here gains importance as: (i) general guidelines to assess the reliability of in-service bridges are non-existent in the Indian context and (ii) the partial factors suggested for two consequence classes can be used for quick assessment of the safety of existing similar flyover girders against limit state of shear in a more rational way.

Keywords

Assessment, RC T Girder Bridges, Partial Factors, Reliability Index.
User
Notifications
Font Size

  • Maljaars, J., Steenbergen, R., Abspoel, L. and Kolstein, H., Safety assessment of existing highway bridges and viaducts. Struct. Eng. Int., 2012, 22(1), 112–120.

  • Steenbergen, R. D. J. M., De Boer, A. and Van der Veen, C., Calibration of partial factors in the safety assessment of existing concrete slab bridges for shear failure. Heron, 2012, 57, 55–68.

  • Vrouwenvelder, T., Codes of practice for the assessment of existing structures. IABSE Reports, 1993, 5.

  • Allen, D. E., Safety criteria for the evaluation of existing structures IABSE reports: Rapports AIPC: IVBH reports, 1993, pp. 77–84.

  • Holicky, M., Markova, J. and Sykora, M., Partial factors for assessment of existing reinforced concrete bridges. Proceedings of the 6th International Probabilistic Workshop, Darmstadt, 2008, pp. 117–132.

  • Vrouwenvelder, A. C. W. M. and Siemes, A. J. M., Probabilistic calibration procedure for the derivation of partial safety factors for the Netherlands building codes. Heron, 1987, 32(4), 9–29.

  • Steenbergen, Raphael, D. J. M. and Vrouwenvelder, A. C. W. M., Safety philosophy for existing structures and partial factors for traffic loads on bridges. Heron, 2010, 55(2), 123–140.

  • Ellingwood, B., MacGregor, J. G., Galambos, T. V. and Cornell, C. A., Probability based load criteria: load factors and load combinations. ASCE, J. Struct. Div., 1982, 108, N0. ST5, 978–997.

  • Stewart, M. G. and Rosowsky, D. V., Time-dependent reliability of deteriorating reinforced concrete bridge decks. Struct. Saf., 1998, 20(1), 91–109.

  • Enright, M. P. and Frangopol, D. M., Reliability-based condition assessment of deteriorating concrete bridges considering load redistribution. Struct. Saf., 1999, 21(2), 159–195.

  • Dimitri, V. V. and Stewart, M. G., Safety factors for assessment of existing structures. J. Struct. Eng., 2002, 128(2), 258–265.

  • Brühwiler, E., Proportionality of interventions to restore structural safety of existing bridges. In Applications of Statistics and Probability in Civil Engineering, Taylor & Francis Group, London, 2011, pp. 32–38.

  • EN1990 BS, Basis of structural design. British Standards Institute, London. 2002, pp. 58–61.

  • Ang, H.-S., Alfredo, and Tang, W. H.., Probability Concepts in Engineering Planning and Design, Decision, Risk and Reliability, John Wiley, New York, 1975, vol. 2.

  • WHO, Global Status Report on Road Safety 2013: supporting a decade of action, World Health Organisation, Geneva, Switzerland, 2013, p. 126.

  • Chennai Metropolitan Development Authority (CMDA), Chennai Comprehensive Transportation Study – Executive Summary, 2010; http://www.cmdachennai.gov.in/pdfs/CCTS_Executive_Summary.pdf.

  • EN 1992-1-1 Eurocode 2: Design of Concrete Structures, Section 6.2, pp. 85–87.

  • Kong, F. K. and Evans, R. H., Reinforced and pre-stressed concrete. Springer, 2013.

  • Schlaich, J., Schäfer, K. and Jennewein, M., Toward a consistent design of structural concrete. PCI J., 1987, 32(3), 74–150.

  • IRC 112-2011:Code of Practice for Concrete Road Bridges, Indian Roads Congress, Ministry of Surface Transport, Roads Wing, 2011, pp. 80–97.

  • Ashour, A. F. and Keun-Hyeok, Y., Application of plasticity theory to reinforced concrete deep beams. Morley Symposium on Concrete Plasticity and its Application, University of Cambridge, 2007.

  • ACI 318-08, Building code requirements for structural concrete, American Concrete Institute, International Organization for Standardization, pp. 109–186.

  • Song, J., Kang, W. H., Kim, K. S. and Jung, S., Probabilistic shear strength models for reinforced concrete beams without shear reinforcement. Struct. Eng. Mech., 2010, 11(1), 15.

  • Code, JCSS – Probabilistic Model. Part III Resistance Models–Steel. Joint Committee on Structural Safety, 2001, sections 3.1, 3.2, 3.9.

  • Rackwitz, R. and Flessler, B., Structural reliability under combined random load sequences. Comput. Struct., 1978, 9(5), 89–94.

  • Standard Plans for Highway Bridges: RCC beam and slab super-structure: Indian Roads Congress, Ministry of Surface Transport, Roads Wing, 1993, pp. 129–138.

  • IRC:SP:37-2010 Guidelines for Evaluation of Load carrying Capacity of Bridges, Indian Roads Congress, Ministry of Surface Transport, Roads Wing, 2010, pp. 10–14.

  • Kulicki, J. M., Zolan, P., Chad, M. C., Dennis, R. M. and Andrzej, S. N., Updating the calibration report for AASHTO LRFD code. Final report, NCHRP Project, 2007, 20(7).


Abstract Views: 436

PDF Views: 133




  • Partial Factors for Shear Capacity Assessment of In-Service RC T-Girder Bridges

Abstract Views: 436  |  PDF Views: 133

Authors

N. J. Yogalakshmi
CSIR-Structural Engineering Research Centre, CSIR Campus, Taramani, Chennai 600 113, India
K. Balaji Rao
CSIR-Structural Engineering Research Centre, CSIR Campus, Taramani, Chennai 600 113, India
M. B. Anoop
CSIR-Structural Engineering Research Centre, CSIR Campus, Taramani, Chennai 600 113, India

Abstract


As the infrastructure age, their assessment to carry the loads they are subjected to becomes increasingly important. Also, assessment is needed as part of a regular monitoring programme. Before carrying out a rigorous probabilistic analysis for assessment, it is often required to make a preliminary assessment using simplified procedures, such as that developed using semi-probabilistic approach, in which partial factors are used. In this article an attempt has been made to evolve a framework to determine the partial factors for safety assessment of the in-service T-girder bridges in India against the limit state of shear. Limit state of shear is considered because it is one of the important ultimate limit states for bridge girder that results in brittle failure. The partial factors are derived using first order reliability method. In order to suggest a simple method for safety assessment, statistical properties of modelling error associated with the simplified equation of shear capacity estimation are estimated using test data of 185 beams reported in the literature. To demonstrate the usefulness of the framework developed, an attempt has been made to determine partial factors for assessment for a typical T-girder bridge designed according to the relevant Indian codes. The loading considered corresponds to actual traffic loads on a typical Chennai flyover. The study reported here gains importance as: (i) general guidelines to assess the reliability of in-service bridges are non-existent in the Indian context and (ii) the partial factors suggested for two consequence classes can be used for quick assessment of the safety of existing similar flyover girders against limit state of shear in a more rational way.

Keywords


Assessment, RC T Girder Bridges, Partial Factors, Reliability Index.

References





DOI: https://doi.org/10.18520/cs%2Fv113%2Fi09%2F1710-1718