Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Computer Simulation for Predicting Tractor Engine overloading for Tillage Operations


Affiliations
1 Department of Agricultural and Food Engineering, IIT, kharagpur (W.B.), India
2 Department of Farm Machinery and Power, College of Agricultural Engineering and Technology, Dr. Balasaheb Sawant Konkan Krishi Vidyapeeth, Dapoli, Ratnagiri (M.S.), India
     

   Subscribe/Renew Journal


The primary purpose of agricultural tractors, especially those in the middle to high power range, is to perform field work. Tractor manufacturer needs prediction of tractor field performance data in the tractor design stage itself so that they can optimize the transmission with the engine to give better performance. Engine speed prediction model was developed using Budni tractor test data. Developed engine speed prediction model for 10 engine model was compared with actual data of engine speed, it was found that for all engine models R2 (co-efficient of determination) between predicted and actual engine speed was greater than 0.98. So developed empirical equations can be used in software for predicting engine speed. The field experiments were conducted using a tractor with three different implements viz., 3-bottom mould board plough, 11-tyne cultivator and offset disc harrow. For each operation, the performance parameters such as draft, slip, depth, engine speed and fuel consumption were measured at different combinations of gear and throttle positions. Software in visual basic was developed to predict tractor engine overloading (engine speed drop) for field operations (MB plough, cultivator and disc harrow). The developed software was validated using field data collected in Kanchipuram, Tamil Nadu. For field operation with 2 WD tractor equipped with bias-ply tires and attached with cultivator the deviation of software predicted engine speed (rpm) drop was -16.47 to 26.92 per cent and for draft was -11.07 to 4.65 per cent. For field test with offset disc harrow the deviation of software predicted engine speed (rpm) drop was -17.44 to 15.38 per cent and for draft was -10.98 to 4.76 per cent. For field operation with MB Plough the deviation of software predicted engine speed (rpm) drop was 18.48 to 21.52 per cent and for draft -12.01 to -3.75 per cent.

Keywords

Tractor Engine Overloading, Engine Speed Prediction Model, Visual Basic, Engine Overloading.
Subscription Login to verify subscription
User
Notifications
Font Size


  • Al-Hamed, S.A. and Al-Janobi, A.A. (2001). A programme for predicting tractor performance in Visual C++. Comp. & Electro. Agric., 31: 137–149.
  • Al-Janobi, A. R. (2000). A data acquisition system to monitor performance of fully mounted implements. J. Agric. Engg. Res. 75: 167-175.
  • Bandy, S.M., Babacz, W.A., Searcy, S.W. and Stout, B. A. (1986). Measurement of three point hitch forces on agricultural tractors. SAE, 86 (1255) : 1105-1116.
  • Godwin, R.J. and Dogherty, M.J.O. (2007). Integrated soil tillage force prediction models. J. Terramechanics, 44: 3-14.
  • Grisso, R.D., Kocher, M.F. and Vaughan, D.H. (2003). Predicting tractor fuel consumption. Appl. Engg. Agric., 20 (5): 553-561.
  • Grogan, J. (1987). Microcomputer-based tractor performance monitoring and optimization system. J. Agric. Engg. Res., 38: 227-243.
  • Harris, H.D. (1992). Prediction of tractor engine performance using OECD Standard Test Data. J. Agric. Engg. Res., 53 : 181-193.
  • Harris, H.D. and Pearce, F. (1990). A universal mathematical model of diesel engine performance. J. Agric. Engg. Res., 51:165-176.
  • Scarlett, A.J. (1993). Integration of tractor engine, transmission and implement depth controls: part 2, control systems. J. Agric. Engg. Res., 54 : 89-112.
  • Schrock, M., Matteson, D., Blumanhourst, M. and Thompson, J.G. (1986). A device for aiding gear selection in agricultural tractors. Trans. ASAE, 29(5): 1232-1236.
  • Singh, S., Singh, R.S. and Singh, S.P. (2014). Farm power availability on Indian farms. Agric. Engg. Today, 38(4): 44-52.
  • Wismer, R.D. (1972). Off-road traction prediction for wheeled vehicles. ASAE, 16 : 72- 619.

Abstract Views: 534

PDF Views: 1




  • Computer Simulation for Predicting Tractor Engine overloading for Tillage Operations

Abstract Views: 534  |  PDF Views: 1

Authors

Shrikant S. Sadavarte
Department of Agricultural and Food Engineering, IIT, kharagpur (W.B.), India
Mahesh R. Patil
Department of Farm Machinery and Power, College of Agricultural Engineering and Technology, Dr. Balasaheb Sawant Konkan Krishi Vidyapeeth, Dapoli, Ratnagiri (M.S.), India

Abstract


The primary purpose of agricultural tractors, especially those in the middle to high power range, is to perform field work. Tractor manufacturer needs prediction of tractor field performance data in the tractor design stage itself so that they can optimize the transmission with the engine to give better performance. Engine speed prediction model was developed using Budni tractor test data. Developed engine speed prediction model for 10 engine model was compared with actual data of engine speed, it was found that for all engine models R2 (co-efficient of determination) between predicted and actual engine speed was greater than 0.98. So developed empirical equations can be used in software for predicting engine speed. The field experiments were conducted using a tractor with three different implements viz., 3-bottom mould board plough, 11-tyne cultivator and offset disc harrow. For each operation, the performance parameters such as draft, slip, depth, engine speed and fuel consumption were measured at different combinations of gear and throttle positions. Software in visual basic was developed to predict tractor engine overloading (engine speed drop) for field operations (MB plough, cultivator and disc harrow). The developed software was validated using field data collected in Kanchipuram, Tamil Nadu. For field operation with 2 WD tractor equipped with bias-ply tires and attached with cultivator the deviation of software predicted engine speed (rpm) drop was -16.47 to 26.92 per cent and for draft was -11.07 to 4.65 per cent. For field test with offset disc harrow the deviation of software predicted engine speed (rpm) drop was -17.44 to 15.38 per cent and for draft was -10.98 to 4.76 per cent. For field operation with MB Plough the deviation of software predicted engine speed (rpm) drop was 18.48 to 21.52 per cent and for draft -12.01 to -3.75 per cent.

Keywords


Tractor Engine Overloading, Engine Speed Prediction Model, Visual Basic, Engine Overloading.

References