International Journal of Emerging Trends in Science & Technology

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Control and Automation of Dump Valves in Paper Industrial Process Using Programmable Logic Controller


Affiliations
1 Department of Electrical and Electronics Engineering, M. Kumarasamy College of Engineering, Karur, Tamil Nadu, India
2 Department of Electronics and Instrumentation Engineering, M. Kumarasamy College of Engineering, Karur, Tamil Nadu, India
     

   Subscribe/Renew Journal


In the past, the automation and control has seen an enormous development. The traditional technologies like PLC, SCADA and DCS has greatly influenced the industrial automation process. It can be effectively used in applications ranging from simple control like replacing small number of relays to complex automation problems. This work applies in screening area of the paper industry to separate high density particles while flowing through the tube to the dump valve. This system is called as waste disposal system. In the screening process, destoner separates the high density particles from the weightless useful pulp and the outlet is lead into the dump valve. The dumping and discharging operations of high density particles in the dump valve is controlled by the Programmable Logic Controller which is used for automation and control of the valve movement sequentially and continuously until the pulp is available [1]. Thus by automation of the waste disposal system, time of the manual operator is saved. This proposed system will increase the disposal rate. There is an advantage of low running cost reduced time cycle and increased precision.

Keywords

Automation, Control Valves, Dump Valve, PLC.
User
Subscription Login to verify subscription
Notifications
Font Size

  • R. Netto, and A. Bagri, “Programmable logic controllers,” International Journal of Computer Applications, vol. 77, no. 11, pp. 27-31, September 2013.

  • A. K. Gupta, and S. Padole, “Design and analysis of dump valve in ash handling system using pro-e and ansys software,” International Journal of Innovation in Engineering Research and Management, vol. 1, no. 2, pp. 1-7, April 2014.

  • R. Navarrete, M. F. Rocha, Z. C. Flores, E. Andrade, C. Canto, M. E. Rocha, and M. I. Rocha, “Automation of production and recycling paper tissue using PLC, PAC, HMI and Ethernet / IP,” Journal of Industrial and Intelligent Information, vol. 4, no. 2, pp. 96-103, March 2016.

  • M. Marinuc, and F. Rus, “The effect of particle size and input velocity on cyclone separator process,” Bulletin of the Transilvania University of Braşov, Series II: Forestry, Wood Industry and Agricultural Food Engineering, vol. 4(53), no. 2, pp. 117-122, 2011.

  • M. R. Jadhav, “Design of cyclone and study of its performance parameters,” International Journal of Mechanical Engineering and Robotics Research, vol. 3, no. 4, pp. 247-252, October 2014.

  • G. B. Sakura, and A. Y. T. Leung, “Experimental study of particle collection efficiency of cylindrical inlet type cyclone separator,” International Journal of Environmental Science and Development, vol. 6, no. 3, pp. 160-164, March 2015.

  • M. I. Taiwo, M. A. Namadi, and B. M. James, “Design and analysis of cyclone dust separator,” American Journal of Engineering Research, vol. 5, no. 4, pp. 130-134, 2016.

  • S. Dwivedi, M. Fernandes, and R. D’souza, “A review on PLC based automatic waste segregator,” International Journal of Advanced Research in Computer Engineering and Technology, vol. 5, no. 2, pp. 280-285, February 2016.

  • R. M. Kittali, and A. Sutagundar, “Automation of waste segregation system using programmable logic controller,” International Journal on Emerging Technologies, vol. 7, no. 2, pp. 265-268, 2016.


Abstract Views: 341

PDF Views: 2




  • Control and Automation of Dump Valves in Paper Industrial Process Using Programmable Logic Controller

Abstract Views: 341  |  PDF Views: 2

Authors

B. Balraj
Department of Electrical and Electronics Engineering, M. Kumarasamy College of Engineering, Karur, Tamil Nadu, India
J. Uma
Department of Electronics and Instrumentation Engineering, M. Kumarasamy College of Engineering, Karur, Tamil Nadu, India

Abstract


In the past, the automation and control has seen an enormous development. The traditional technologies like PLC, SCADA and DCS has greatly influenced the industrial automation process. It can be effectively used in applications ranging from simple control like replacing small number of relays to complex automation problems. This work applies in screening area of the paper industry to separate high density particles while flowing through the tube to the dump valve. This system is called as waste disposal system. In the screening process, destoner separates the high density particles from the weightless useful pulp and the outlet is lead into the dump valve. The dumping and discharging operations of high density particles in the dump valve is controlled by the Programmable Logic Controller which is used for automation and control of the valve movement sequentially and continuously until the pulp is available [1]. Thus by automation of the waste disposal system, time of the manual operator is saved. This proposed system will increase the disposal rate. There is an advantage of low running cost reduced time cycle and increased precision.

Keywords


Automation, Control Valves, Dump Valve, PLC.

References