International Journal of Emerging Trends in Science & Technology

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Optimization of Drilling Parameters in Cu-Ni-Tib2 Material Using Taguchi Methodology


Affiliations
1 Department of Mechanical Engineering, M. Kumarasamy College of Engineering, Karur, Tamil Nadu, India
2 Department of Mechatronics, K. S. Rangasamy College of Technology, Tiruchencode, Tamil Nadu, India
     

   Subscribe/Renew Journal


The drilling process is most important in manufacturing industries. In this case various drilling process parameters have been performed to cut the material. This paper mainly focusing on material removal rate and better surface roughness. The various drill holes to produce in Cu-Ni-Tib2 material based on given input parameters of speed, feed and selected drill tool. The optimized input parameters have been finding out in Taguchi L9 orthogonal array. The Cu-Ni-Tib2 material basically High hardness and high corrosion resistivity material using in various industrial applications. The various drilling input control factor precious in Cu-Ni-Tib2 material surface. The output parametric optimization has been performed in thrust force, torque, material removal rate and surface finish based on the results confirmations using in minitab-17 Tool.

Keywords

ANOVA, Drilling, Material Removal Rate (MRR), Surface Roughness.
User
Subscription Login to verify subscription
Notifications
Font Size

  • J. Prasanna, L. Karunamoorthy, M. V. Raman, S. Prashanth, and D. R. Chordia, “Optimization of process parameters of small hole dry drilling in Ti–6Al–4V using Taguchi and grey relational analysis,” Measurement, vol. 48, pp. 346-354, February 2014.

  • L.-A. Mihail “Robust engineering of deep drilling process by surface state optimization,” Procedia CIRP, vol. 8, pp. 582-587, 2013,

  • T. Matsumura, and S. Tamura, “Cutting force model in drilling of multi-layered materials,” Procedia CIRP, vol. 8, pp. 182-187, 2013,

  • A. Taşkesen, and K. Kütükde, “Experimental investigation and multi-objective analysis on drilling of boron carbide reinforced metal matrix composites using grey relational analysis,” Measurement, vol. 47, pp. 321-330, January 2014.

  • P. Mayuet, A. Gallo, A. Portal, P. Arroyo, M. Alvarez, and M. Marcos, “Damaged area based study of the break-in and break-out defects in the dry drilling of Carbon Fiber Reinforced Plastics (CFRP),” Procedia Engineering, vol. 63, pp. 743-751, 2013.

  • A. Taskesen, and K. Kutukde, “Analysis and optimization of drilling parameters for tool wear and hole dimensional accuracy in B4C reinforced Al-alloy,” Transactions of Nonferrous Metals Society of China, vol. 23, no. 9, pp. 2524-2536, September 2013.

  • R. Zitoune, V. Krishnaraj, and F. Collombet, “Study of drilling of composite material and aluminium stack,” Composite Structures, vol. 92, no. 5, pp. 1246-1255, April 2010.

  • W. C. Lyons, and G. J. Plisga, Standard Handbook of Petroleum and Natural Gas Engineering, 2nd ed., pp. 1-565, 2004.

  • M. E. Portman, “Regulatory capture by default: Offshore exploratory drilling for oil and gas,” Energy Policy, vol. 65, pp. 37-47, February 2014.

  • R. K. Pandey, and S. S. Panda, “Optimization of bone drilling parameters using grey-based fuzzy algorithm,” Measurement, vol. 47, pp. 386-392, January 2014.

  • S. Sánchez-Beitia, and L. Schueremans, “The hole drilling technique for on site deduction of the stresses states in stone masonry by using eight strain gages,” Construction and Building Materials, vol. 23, no. 5, pp. 2041-2046, May 2009.

  • N. Parthipan, and C. Manickam, “Multi objective optimization for drilling process stresses in SS317 material,” International Journal of Mechanical and Production Engineering Research and Development, vol. 8, no. 2, pp. 781-790, April 2018.

  • A. Manikandan, and N. Parthipan, “Fabrication of metal matrix composite for brake drum-a characteristic study of tribological properties,” International Journal of Mechanical and Production Engineering Research and Development, vol. 8, no. 2, pp. 811-818, April 2018.

  • N. Parthipan, S. C. Prasanna, R. Balamurugan, and A. Manikandan, “Optimization parameters of drilling process in electric discharge machining used in SS317 material,” Pak. J. Biotechnol., vol. 14, sp. issue 1 (International Conference on Futuristic Innovations in Mechanical Engineering and Manufacturing Management), pp. 99-102, 2017.


Abstract Views: 322

PDF Views: 0




  • Optimization of Drilling Parameters in Cu-Ni-Tib2 Material Using Taguchi Methodology

Abstract Views: 322  |  PDF Views: 0

Authors

N. Parthipan
Department of Mechanical Engineering, M. Kumarasamy College of Engineering, Karur, Tamil Nadu, India
M. Ilangkumaran
Department of Mechatronics, K. S. Rangasamy College of Technology, Tiruchencode, Tamil Nadu, India

Abstract


The drilling process is most important in manufacturing industries. In this case various drilling process parameters have been performed to cut the material. This paper mainly focusing on material removal rate and better surface roughness. The various drill holes to produce in Cu-Ni-Tib2 material based on given input parameters of speed, feed and selected drill tool. The optimized input parameters have been finding out in Taguchi L9 orthogonal array. The Cu-Ni-Tib2 material basically High hardness and high corrosion resistivity material using in various industrial applications. The various drilling input control factor precious in Cu-Ni-Tib2 material surface. The output parametric optimization has been performed in thrust force, torque, material removal rate and surface finish based on the results confirmations using in minitab-17 Tool.

Keywords


ANOVA, Drilling, Material Removal Rate (MRR), Surface Roughness.

References