International Journal of Vehicle Structures and Systems

Open Access Open Access  Restricted Access Subscription Access

Modeling and Simulation of Off-Road Vehicle Mobility with Driving Torque Distribution Control on Split Adhesion Conditions


Affiliations
1 Dept. of Automotive and Tractors Engg., Helwan University, Cairo, Egypt
 

   Subscribe/Renew Journal


This paper presents a theoretical model for simulation of driving torque distribution control to improve off-road vehicle mobility on split adhesion conditions. The model is constructed and then validated with experimental test rig results. A MATLAB simulink modeling of an electronically controlled device is used to modulate the applied force over multi-plate clutches located between the automotive driven axle shafts and the stationary hub. On driving over split adhesion roads, the control device brakes the spinning axle wheel running over ground low adhesion side and accordingly biases more torque to the other wheel with good adhesion side. This would improve the vehicle off-road mobility and save the power losses on low adhesion wheels. The proposed control model had been validated with experimental results obtained from an experimental tests conducted on a specially designed and built test rig. Consequently, the proposed control system has been embedded within a full car theoretical model to predict the vehicle performance on split adhesion drive conditions. The results showed that the constructed simulink model is suitable for simulating the proposed controlled device for torque distribution after matching the simulation results with experimental test rig results. Moreover, the proposed control model could be implemented to improve the transmitted traction power to the road from a conventional deferential.

Keywords

Off-Road Vehicle, Automotive Torque Distribution, Driving Torque Distribution Control, Matlab Simulink.
User
Subscription Login to verify subscription
Notifications
Font Size

  • S.S. Gill, S. Nirmal, S. Balraj and S. Neetu. 2002. Improved differential function for avoiding slippage of motor vehicles in a muddy trench, SAE Technical Paper, 2002-01-0988.

  • S. Shih and W. Bowerman. 2002. An evaluation of torque bias and efficiency of Torsen differential, SAE Technical Paper, 2002-01-1046.

  • R. Holzwarth and K. May. 1994. Analysis of traction control systems augmented by limited slip differentials, SAE Technical Paper, 940831.

  • J. Park, J. Dutkiewicz and K. Cooper. 2005. Simulation and control of Dana’s active limited slip differential E-diff., SAE Technical Paper, 2005-01-0409.

  • P.O. Russell and S. Taehyun. 2004. Independent control of all-wheel-drive torque distribution, SAE Technical Paper, 2004-01-2052.

  • H. Huchtkoetter and H. Klein. 1996. The effect of various limited-slip differentials in front-wheel drive vehicles on handling and traction, SAE Technical Paper, 960717.

  • C.W. Jonathan. 2005. Torque vectoring driveline: SUV-based demonstrator and practical actuation technologies, SAE Technical Paper, 2005-01-0553.

  • C. Liu, V. Monkaba, H. Tan, C. Mc Kenzie, H. Lee and S. Suo. 2002. Driveline torque-bias-management modeling for vehicle stability control, SAE Technical Paper, 2002-01-1584.

  • B. Mashadi, S. Mostaani and M. Majidi. 2011. Vehicle stability enhancement by using an active differential, J. Systems and Control Engg., 225(8), 1098-1114. https://doi.org/10.1177/0959651811405113.

  • D. Josko, I. Vladimir, H. Matthew and A. Francis. 2010. Modeling and analysis of active differential dynamics, J.Dynamic Systems Measurement and Control, 132(6).

  • V. Ivanovic, J. Deur, Z. Herold, M. Hancock and F. Assadian. 2011. Modelling of electromechanically actuated active differential wet-clutch dynamics, Proc. IMechE, Part D: J. Automobile Engg., 226, 433-456.

  • https://doi.org/10.1177/0954407011423131.

  • L. Lifu and W. Zhan. 2011. Study on torque vectoring differential for vehicle stability control via hardware in-loop simulation, IEEE Paper, 978-1-61284-486.

  • M.A. El-Hafiz. 2012. Axle Torque Distribution Control for Enhancing Off-road Vehicle Performance, PhD. Thesis, Faculty of Engg., Helwan University, Mattaria.

  • M.A. El-Hafiz, M. Emam, W. Oraby and S. Shaaban. 2014. Axle torque distribution control for enhancing mobility of off-road vehicles, Int. J. Heavy Vehicle Systems, 21(3).


Abstract Views: 335

PDF Views: 199




  • Modeling and Simulation of Off-Road Vehicle Mobility with Driving Torque Distribution Control on Split Adhesion Conditions

Abstract Views: 335  |  PDF Views: 199

Authors

M. M. Abd El-Hafiz
Dept. of Automotive and Tractors Engg., Helwan University, Cairo, Egypt
M. A. A. Emam
Dept. of Automotive and Tractors Engg., Helwan University, Cairo, Egypt
W. A. H Oraby
Dept. of Automotive and Tractors Engg., Helwan University, Cairo, Egypt
S. Shaaban
Dept. of Automotive and Tractors Engg., Helwan University, Cairo, Egypt

Abstract


This paper presents a theoretical model for simulation of driving torque distribution control to improve off-road vehicle mobility on split adhesion conditions. The model is constructed and then validated with experimental test rig results. A MATLAB simulink modeling of an electronically controlled device is used to modulate the applied force over multi-plate clutches located between the automotive driven axle shafts and the stationary hub. On driving over split adhesion roads, the control device brakes the spinning axle wheel running over ground low adhesion side and accordingly biases more torque to the other wheel with good adhesion side. This would improve the vehicle off-road mobility and save the power losses on low adhesion wheels. The proposed control model had been validated with experimental results obtained from an experimental tests conducted on a specially designed and built test rig. Consequently, the proposed control system has been embedded within a full car theoretical model to predict the vehicle performance on split adhesion drive conditions. The results showed that the constructed simulink model is suitable for simulating the proposed controlled device for torque distribution after matching the simulation results with experimental test rig results. Moreover, the proposed control model could be implemented to improve the transmitted traction power to the road from a conventional deferential.

Keywords


Off-Road Vehicle, Automotive Torque Distribution, Driving Torque Distribution Control, Matlab Simulink.

References





DOI: https://doi.org/10.4273/ijvss.9.2.07