International Journal of Vehicle Structures and Systems

Open Access Open Access  Restricted Access Subscription Access

Geometric Design Validation of Oxidation Catalysis System in Composite Regeneration Emission Control System


Affiliations
1 Dept. of Mech. Engg., University of Petroleum and Energy Studies, Dehradun, India
 

   Subscribe/Renew Journal


Development of emission control systems for reducing the toxicity levels of exhaust emissions is one of the major challenges faced by automotive industry which rely on diesel engines owing to its thermal efficiency and service life. The major challenge faced for implementation of emission control system is the periodic regeneration of channels in diesel particulate filter to avoid clogging and backpressure rise inside the substrate. Commercial fuel based regeneration is leading to uncontrolled combustion inside the filter substrate affecting its service life. State of art of the emission control system has been detailed by conducting literature survey on the area and it has been found that these systems have a vital role in reducing emission levels to meet emission norms. Microwave based active regeneration has been proposed in this paper to improve the service life and effectiveness of diesel particulate filter. Three dimensional models of the axial flow, radial flow and cylindrical oxidation catalysis system are developed using Computer Aided Design software and flow analysis has been conducted using Computational Fluid Dynamics software (ANSYS FLUENT). Validation of the geometric design is done using simulation results and the pressure drop across the system is found to be in acceptable range.

Keywords

Computational Fluid Dynamics, Catalyst, Design, Emissions, Filtration, Particulate.
User
Subscription Login to verify subscription
Notifications
Font Size

  • D. Carder, R. Ryskamp, M. Besch and A. Thiruvengadam. 2017. Emissions control challenges for compression ignition engines, Proc. IUTAM, Int. Congress of Theoretical and Applied Mechanics, 20(10), 103-111. https://doi.org/10.1016/j.piutam.2017.03.015.

  • D. Bose, C. Kurien, A. Sharma, S. Sharma and A. Sharma. 2018. Low cost cathode performance of microbial fuel cell for treating food wastewater, Nature Environ. Pollut. Tech., 17(3), 853-856.

  • C. Kurien and A.K. Srivastava. 2018. Advancement in the design of automotive catalytic filter for meeting environmental emission norms key words, Nature Environ. Pollut. Tech., 17(2), 433-438.

  • V. Bermúdez, J.R. Serrano, P. Piqueras and O. GarcíaAfonso. 2015. Pre-DPF water injection technique for pressure drop control in loaded wall-flow diesel particulate filters, Appl. Energy, 140, 234-245. https://doi.org/10.1016/j.apenergy.2014.12.003.

  • V. Palma, P. Ciambelli, E. Meloni and A. Sin. 2015 Catalytic DPF microwave assisted active regeneration, Fuel, 140, 50-61. https://doi.org/10.1016/j.fuel.2014.09.051.

  • S. Ye, Y.H. Yap, S.T. Kolaczkowski, K. Robinson and D. Lukyanov. 2011. Catalyst ‘light-off’ experiments on a diesel oxidation catalyst connected to a diesel engine Methodology and techniques, Chem. Engg. Res. Des., 90(6), 834-845. https://doi.org/10.1016/j.cherd.2011.10.003.

  • H. Xiong, E. Peterson, G. Qi and A.K. Datye. 2016. Trapping mobile Pt species by PdO in diesel oxidation catalysts : Smaller is better, Catal. Today, 272, 80-86. https://doi.org/10.1016/j.cattod.2016.01.022.

  • M.V. Twigg. 2005. Development of platinum catalysts and their use in the control of vehicle exhaust emissions, Appl. Earth Sci., 114(3), 158-172. https://doi.org/10.1179/037174505X45540.

  • A.Z. Taibani and V. Kalamkar. 2012. Experimental and computational analysis of behaviour of three-way catalytic converter under axial and radial flow conditions, Int. J. Fluid Mach. Syst., 5(3), 134-142. https://doi.org/10.5293/IJFMS.2012.5.3.134.

  • D. Fino, S. Bensaid, M. Piumetti and N. Russo. 2016. A review on the catalytic combustion of soot in diesel particulate filters for automotive applications: From powder catalysts to structured reactors, Appl. Catal. A Gen., 509, 75-96. https://doi.org/10.1016/j.apcata.2015.10.016.

  • H. Huang, B. Jiang, L. Gu, Z. Qi and H. Lu. 2015. Promoting effect of vanadium on catalytic activity of Pt/Ce-Zr-O diesel oxidation catalysts, J. Environ. Sci., 33, 135-142. https://doi.org/10.1016/j.jes.2014.10.026.

  • M.M. Azis, X. Auvray, L. Olsson and D. Creaser. 2015. Evaluation of H2 effect on NO oxidation over a diesel oxidation catalyst, Appl. Catal. B Environ., 179(2), 542-550. https://doi.org/10.1016/j.apcatb.2015.05.054.

  • A. Arvajová, P. Kočí, V. Schmeißer and M. Weibel. 2016. The impact of CO and C3H6 pulses on PtOx reduction and NO oxidation in a diesel oxidation catalyst, Appl. Catal. B Environ., 181, 644-650. https://doi.org/10.1016/j.apcatb.2015.08.004.

  • T. Tang, J. Zhang, D. Cao, S. Shuai and Y. Zhao. 2014. Experimental study on filtration and continuous regeneration of a particulate filter system for heavy-duty diesel engines, J. Environ. Sci., 26(12), 2434-2439. https://doi.org/10.1016/j.jes.2014.04.004.

  • V. Palma, E. Meloni, M. Caldera, D. Lipari, V. Pignatelli and V. Gerardi. 2016. Catalytic wall flow filters for soot abatement from biomass boilers, Chem. Engg. Trans., 50, 253-258.

  • C. Kurien, A.K. Srivastava and J. Naudin. 2018. Modelling of regeneration and filtration mechanism in diesel particulate filter for development of composite regeneration emission control system, Arch. Mech. Engg., 65(2), 277-290.

  • C. Kurien and A.K. Srivastava. 2018. Active regeneration of diesel particulate filter using microwave energy for exhaust emission control, Intelligent Communication, Control and Devices, 1233-1241.

  • V.R. Pérez and A. Bueno-López. 2015. Catalytic regeneration of diesel particulate filters: comparison of Pt and Ce Pr active phases, Chem. Engg. J., 279, 79-85. https://doi.org/10.1016/j.cej.2015.05.004.

  • G. Corro, S. Cebada, U. Pal, J.L.G. Fierro and J. Alvarado. 2015. Hydrogen-reduced Cu/ZnO composite as efficient reusable catalyst for diesel particulate matter oxidation, Appl. Catal. B Environ., 165, 555-565. https://doi.org/10.1016/j.apcatb.2014.10.048.

  • T. Qiu, X. Li, H. Liang, X. Liu and Y. Lei. 2014. A method for estimating the temperature downstream of the SCR (selective catalytic reduction) catalyst in diesel engines, Energy, 68, 311-317. https://doi.org/10.1016/j.energy.2014.02.101.

  • R.O.M. Clellan, T.W. Hesterberg and J.C. Wall. 2012. Evaluation of carcinogenic hazard of diesel engine exhaust needs to consider revolutionary changes in diesel technology, Regul. Toxicol. Pharmacol., 63(2), 225-258. https://doi.org/10.1016/j.yrtph.2012.04.005.

  • P. Jiao, Z. Li, B. Shen, W. Zhang, X. Kong and R. Jiang. 2017. Research of DPF regeneration with NOx-PM coupled chemical reaction, Appl. Therm. Engg., 110(Supplement C), 737-745. https://doi.org/10.1016/j.applthermaleng.2016.08.184.

  • K. Abay and U. Colak. 2018. Computational fluid dynamics analysis of flow and combustion, J. Therm. Engg., 4(2), 1878-1895. https://doi.org/10.18186/journal-of-thermal-engineering.388333.

  • C.G.B. Yoon and G. Cho. 2009. Study of design & CFD analysis for partial dpf utilizing metal foam, Trans. Korean Soc. Automot. Engg., 17(1), 24-34.

  • F. Fornarelli, S. Camporeale, R. Dadduzio, B. Fortunato and M. Torresi. 2015. Numerical simulation of the flow field and chemical reactions within a NSC diesel catalyst, Energy Proc., 82(10), 381-388. https://doi.org/10.1016/j.egypro.2015.11.811.

  • R.E. Hayes, A. Fadic, J. Mmbaga and A. Najafi. 2012. CFD modelling of the automotive catalytic converter, Catal. Today, 188(1), 94-105. https://doi.org/10.1016/j.cattod.2012.03.015.


Abstract Views: 608

PDF Views: 211




  • Geometric Design Validation of Oxidation Catalysis System in Composite Regeneration Emission Control System

Abstract Views: 608  |  PDF Views: 211

Authors

Caneon Kurien
Dept. of Mech. Engg., University of Petroleum and Energy Studies, Dehradun, India
Ajay Kumar Srivastava
Dept. of Mech. Engg., University of Petroleum and Energy Studies, Dehradun, India
Deepak Kumar
Dept. of Mech. Engg., University of Petroleum and Energy Studies, Dehradun, India

Abstract


Development of emission control systems for reducing the toxicity levels of exhaust emissions is one of the major challenges faced by automotive industry which rely on diesel engines owing to its thermal efficiency and service life. The major challenge faced for implementation of emission control system is the periodic regeneration of channels in diesel particulate filter to avoid clogging and backpressure rise inside the substrate. Commercial fuel based regeneration is leading to uncontrolled combustion inside the filter substrate affecting its service life. State of art of the emission control system has been detailed by conducting literature survey on the area and it has been found that these systems have a vital role in reducing emission levels to meet emission norms. Microwave based active regeneration has been proposed in this paper to improve the service life and effectiveness of diesel particulate filter. Three dimensional models of the axial flow, radial flow and cylindrical oxidation catalysis system are developed using Computer Aided Design software and flow analysis has been conducted using Computational Fluid Dynamics software (ANSYS FLUENT). Validation of the geometric design is done using simulation results and the pressure drop across the system is found to be in acceptable range.

Keywords


Computational Fluid Dynamics, Catalyst, Design, Emissions, Filtration, Particulate.

References





DOI: https://doi.org/10.4273/ijvss.11.1.16