Open Access
Subscription Access
Open Access
Subscription Access
Tribomechanical Investigation on Aluminum Metal Matrix Composite with Silicon Carbide, Waste Egg Shells and Boron Carbide as Reinforcements
Subscribe/Renew Journal
Need of global development in research, industries and defense applications promote researchers to deal with composites. This paper aims to analyze all the tribomechanical characteristics by fabricating aluminum (Al) alloy altering the volume percentage of reinforcements like silicon carbide (SiC), waste carbonized egg shells (WCE) and boron carbide (B4C) by stir casting. Experimental results shows increase of tensile strength, fatigue strength and hardness up to 12.5 wt.% in Al matrix alloy, but then decreases. Also toughness and ductility decreases at the same reinforcement conditions. Heat treatment was done to improve the corrosion rate of the composites. The results inferred that using WCE gave better physical and mechanical properties at lower cost than uncarbonized egg shells (ES) or SiC or B4C.
Keywords
Waste Carbonized Eggshells, Wettability, Preheat Temperature, Porosity, Corrosion Rate.
User
Subscription
Login to verify subscription
Font Size
Information
- Selvam, J.D.R., Smart, D.S.R., Dinaharan, I., Microstructure and some mechanical properties of fly ash particulate reinforced AA aluminum alloy composites prepared by compocasting, Material and Design, Vol.49, pp.28–34, 2013.
- Aribo, S., Omotoyinbo, J.A., Folorunso, D.O., High temperature mechanical properties of silicon carbide particulate reinforced cast aluminium alloy composite, Leonardo Electronic Journal of Practices and Technologies, Vol.18, pp.9–16, 2011.
- Daoud, A., Abou-Elkhair, M.T., Rohatgi, P., Wear and friction behavior of near eutectic Al–Si+ZrO2 or WC particle composites, Composite Science and Technology, Vol.64, pp.1029–1040, 2004.
- Prasad, V.V.B., Prasad, K.S., Kurovilla, A.K., Pandey, A.B., Bhat, B.V.R., Mahajan, Y.R., Composite strengthening in 6061 and Al-4 Mg alloys, Journal of Materials Science, Vol.26, pp.460–465, 1991.
- Marin, E., Lekka, M., Andreatta, F., Fedrizzi, I., Itskos, G., Moutsatsou, A., Koukouzas, N., Kouloumbi, N., Electrochemical study of aluminum-fly ash composite obtained by powder metallurgy, Materials Characterization, Vol.69, pp.16–30, 2012.
- Wu, Y. and Lavemia, E., Proceedings: Conference Advancements in Synthesis and Processes, Toronto, Society for Advancement of Material and Process Engineering, M692, 1992.
- Tiwari, R., Herman, H., Sampath, S., Gudmundsson,B., Plasma spray consolidation of high temperature composites, Material Science and Engineering, A144, pp.127–133, 1991.
- Kim, S.W., Lee, U.J., Han, S.W., Kim, D.K., Ogi, K., Heat treatment and wear characteristics of Al/SiCp composites fabricated by duplex process, Composites: Part B, Vol.34, pp.737–745, 2003.
- Amirkhanlou, S., Rezaei, M.R., Niroumand, B., Toroghinejad, M.R., High-strength and highly-uniform composites produced by compocasting and cold rolling processes, Material and Design, Vol.32, pp.2085–2090, 2011.
- Hassan, S.B., and Aigbodion, V.S., Effects of Eggshell on the Microstructures and Properties of Al-Cu-Mg/Eggshell Particulate Composites, Journal of King Saud University-Engineering Sciences, Vol.27, pp.49-56, 2015.
- Deep, G., Idrisi, A.H., Siddiqui, T.U., A New Bio-Filler for Polypropylene Composites, International Journal of Innovative Research in Science, Engineering and Technology, Vol.5, pp.16720-16725, 2016.
- Kayal, S., Behera, R, Nandi, T., Sutradhar, G., Solidification behavior of stir cast Al alloy metal matrix composites, International Journal of Applied Engineering Research, Dindigul, Vol.2, pp.350-359, 2011.
- Jyothi P.N., Bharath Kumar B.S., Comparison of Mechanical Properties of Al-5%Si Alloy Reinforced with Cow dung ash and Rice husk ash, International Journal of Latest Research in Engineering and Technology, Vol.1, pp.55-58, 2015.
- Alaneme, K.K., Olubambi, P.A., Corrosion and wear behavior of rice husk ash alumina reinforced Al_Mg_Si alloy matrix hybrid composites, Journal of Materials Research and Technology, Vol.2, pp.188–194, 2013.
- Emenike, R.O., Corrosion Behaviour of fly ash reinforced Aluminium Magnesium Alloy A535 Composite, MSc. Thesis, University of Saskatchewan, Canada, pp.3–4.
- Prasad, S.D., Krishna, R.A., Tribological Properties of A356.2/RHA Composite, Journal of Material Science and Technology, Vol.33, pp.51–58, 2011.
- Aribo, S., Barker, R., Hu, X., Neville, A., Erosion-corrosion behavior of lean duplex stainless steels in 3.5% NaCl solution, Wear, Vol.302, pp.1602–1608, 2013.
- Dwivedi, S.P., Sharma, S., Mishra, R.K., Characterization of Waste Eggshells and CaCO3 Reinforced AA2014 Green Metal Matrix Composites: A Green Approach in the Synthesis of Composites, International Journal of Precision Engineering and Manufacturing, Vol.17, pp.1383-1393, 2016.
- Kumar, K.C.K., Raju, T.N., Laxmi, Y.N., Studies on Al6061-B4C metal matrix composites fabricated by stir casting process. SSRG International Journal of Mechanical Engineering, pp.296-299, 2017.
- Mohanavel, V., Rajan, K., Senthil, P.V., Arul, S., Mechanical behaviour of hybrid composite (AA6351+Al2O3+Gr) fabricated by stir casting method, Materials Today: Proceedings, Vol.4, pp.3093–3101 2017.
Abstract Views: 1627
PDF Views: 11