Manufacturing Technology Today

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Experimental Analysis of Piercing in Titanium Alloy using Abrasive Waterjet Machinei


Affiliations
1 Dept. of Mechanical Engg, T. S. Srinivasan Centre for Polytechnic College and Advanced Training Vanagaram, Chennai, India
     

   Subscribe/Renew Journal


Abrasive Water Jet Machining (AWJM) is one of the fastest growing non- traditional machining processes, which uses highly pressurized water mixed with abrasive particles and is capable of cutting even difficult-to-cut materials. It is used in the manufacturing of components with intricate shapes and profiles. Here the experimentation is conducted on abrasive water jet (AWJ) machining of the most commonly used titanium alloy, Ti-6Al-4V. It is significantly stronger than commercially pure titanium while having the same stiffness and thermal properties The machining operations, i.e. drilling (or piercing), were conducted. For the experiments, the influences of water pressure and drilling time, mesh size and abrasive flow rate were investigated.

The experiments are carried out based on Response Surface Methodology (RSM) designed using Box-Behnken method for four parameters into three levels. Using response surface graphs the significant AWJM machining parameters and their levels are identified to achieve depth of cut, hole diameter and kerf width.


Keywords

Abrasive Water Jet Machining, Piercing, Titanium Alloy.
User
Subscription Login to verify subscription
Notifications
Font Size

  • Chen, Y; Li, H; Wang, J: Analytical modelling of cutting forces in near-orthogonal cutting of titanium alloy, 'Ti6Al4V. J Mech Eng Sci', vol. 229, no. 6 2015, 1122–1133.

  • Wang, J; Guo, DM: A predictive depth of penetration model for abrasive waterjet cutting of polymer matrix composites, 'J. Mater Process Technology', vol. 121, no. 2–3, 2002, 390–394.

  • Axinte, DA; Karpuschewski, B; Kong, MC; Beaucamp, AT; Anwar, S; Miller, D; Petzel, M: High Energy Fluid Jet Machining (HEFJetMach): from scientific and technological advances to niche industrial applications, 'CIRP Ann Manuf Technol', vol. 63, no.2, 2014, 751–771.

  • Finnie, I: The Mechanism of Erosion of Ductile Metals. Proceedings of the 3rd U.S. National Congress of Applied Mechanics, New York, USA, 1958, 527–532.

  • Bitter, JGA: A study of erosion phenomena part I, 'Wear', vol. 6, no.1,1963,5–21.

  • Hashish, M: Amodeling study of metal cutting with abrasive waterjets. 'ASME Trans J Eng Mater Technol', vol. 106, 1984, 88–100

  • Li, W; Wang, J; Zhu, H; Li, H; Huang, C: On ultrahigh velocity micro-particle impact on steels–a single impact study, 'Wear', vol. 35, no. 1– 2, 2013,216–227

  • Seo, YW; Ramulu, M; Kim, D: Machinability of titanium alloy (Ti-6Al-4V) by abrasive waterjets, 'Proc Inst MechEng B J Eng Manuf', vol. 217, 2003, 1709–1721.3

  • Fowler, G; Shipway, PH; Pashby, IR: Abrasive water-jet controlled depth milling of Ti6Al4V alloy-an investigation of the role of jet-workpiece traverse speed and abrasive grit size on the characteristics of the milled material, 'J Mater Process Technol', vol. 161, no. 3, 2004, 407–414.

  • Shipway, P; Fowler, G; Pashby, IR: Characteristics of the surface of a titanium alloy following milling with abrasive waterjet, 'Wear', vol. 258, no.1, January 2005,123-132.

  • Hascalik, A; Caydas, U; Gurun, H: Effect of traverse speed on abrasive waterjet machining of Ti-6Al-4V alloy, 'Mater Des', 28, 2007 1953–1957.

  • Wang, J: Predictive depth of jet penetration models for abrasive waterjet cutting of alumina ceramics, 'Int J Mech Sci', vol. 49, 2007,306– 316.

  • Hlavac, ML: Investigation of the abrasive waterjet trajectory curvature inside the kerf, 'J Mater Process Technol' vol. 209, 2009, 4154–4161.

  • Orbanic, H; Junkar, M:An experimental study of drilling small and deep blind holes with an abrasive water jet, 'Proc Inst MechEng B J Eng Manuf', vol. 218, no. 2004, 503–508.

  • Boud, F; Carpenter, C; Folkes, J; Shipway, PH: Abrasive waterjet cutting of a titanium alloy: the influence of abrasive morphology and mechanical properties on workpiece grit embedment and cut quality, 'J Mater Process Technol', vol. 210, 2010, 2197–2205.

  • Gent, M; Menendez, M; Torno, S; Torano, J; Schenk, A: Experimental evaluation of the physical properties required of abrasives for optimizing waterjet cutting of ductile materials, 'Wear', vol. 284–285, 2012, 43–51


Abstract Views: 234

PDF Views: 0




  • Experimental Analysis of Piercing in Titanium Alloy using Abrasive Waterjet Machinei

Abstract Views: 234  |  PDF Views: 0

Authors

K. Hemaprasad
Dept. of Mechanical Engg, T. S. Srinivasan Centre for Polytechnic College and Advanced Training Vanagaram, Chennai, India
R. Micheal Nirml Kumar
Dept. of Mechanical Engg, T. S. Srinivasan Centre for Polytechnic College and Advanced Training Vanagaram, Chennai, India

Abstract


Abrasive Water Jet Machining (AWJM) is one of the fastest growing non- traditional machining processes, which uses highly pressurized water mixed with abrasive particles and is capable of cutting even difficult-to-cut materials. It is used in the manufacturing of components with intricate shapes and profiles. Here the experimentation is conducted on abrasive water jet (AWJ) machining of the most commonly used titanium alloy, Ti-6Al-4V. It is significantly stronger than commercially pure titanium while having the same stiffness and thermal properties The machining operations, i.e. drilling (or piercing), were conducted. For the experiments, the influences of water pressure and drilling time, mesh size and abrasive flow rate were investigated.

The experiments are carried out based on Response Surface Methodology (RSM) designed using Box-Behnken method for four parameters into three levels. Using response surface graphs the significant AWJM machining parameters and their levels are identified to achieve depth of cut, hole diameter and kerf width.


Keywords


Abrasive Water Jet Machining, Piercing, Titanium Alloy.

References