Open Access
Subscription Access
Open Access
Subscription Access
Analysis of Effect of Cutting Parameters on Surface Roughness and Cutting Force During Turning of Aluminum Alloy (AlSi5Cu3)
Subscribe/Renew Journal
The aim of this research work is focused on analysis of process parameters during turning of aluminium alloy (AlSi5Cu3). A study of effect of cutting parameters in turning of Aluminum Alloy (AlSi5Cu3) on the cutting force generated and machined surface roughness is carried out. In the experiment conducted, six values of feed rate, three values of depth of cut, and two values of cutting speed respectively, are used. The test pieces were turned on a centre lathe machine with different levels of cutting parameters by using full factorial design of experiment orthogonal array. The surface roughness of the machined surface was measured using surface measurement tester. Taguchi methodology was used to optimize process parameters. The results were analyzed by using Analysis of variance. From result analysis, it was found that, feed rate played a major role in producing lower surface roughness followed by cutting speed whereas depth of cut has least significance in producing lower surface roughness. To achieve better machining performance, the optimum condition parameters for surface roughness and cutting force, are as feed rate (FR = 0.045 m/min.), the cutting speed (CS = 90 m/min.), depth of cut (DOC = 0.5 mm). From analysis it is also seen that the cutting force equation and surface roughness equations are appropriate for accurate prediction. Thus, with proper selection of cutting parameters, it is possible to achieve good surface roughness, reduce tool wear while maintaining the cutting forces and temperatures at reasonable levels.
Keywords
Turning, Surface Roughness, Cutting Force, Cutting Parameters.
User
Subscription
Login to verify subscription
Font Size
Information
- Amini, S., Khakbaz, H., & Barani, A. (2015). Improvement of Near-Dry Machining and It’s Effect on Tool Wear in Turning of AISI 4142. Journal of Materials and Manufacturing Processes, 30, 241–247.
- Aouici, H., Yallese, M. A., Belbah, A., Mfameur & Elbah, M. (2013). Experimental Investigation of Cutting Parameters Influence on Surface Roughness and Cutting Forces in Hard Turning of X38CrMoV5-1 with CBN tool. Journal of Sadhana Indian Academy of Sciences, 38 (Pt 3), 429-445.
- Chen Lu (2008). Study on Prediction of Surface Quality in Machining Process. Journal of Materials Processing Technology, 205, 439-450.
- CMTI (1982). Machine Tool Design Handbook. Tata Mc-Graw Hill, New Delhi, 637-650.
- Montgomery, D. C. (2001). Design and Analysis of Experiments. John Wiley and Sons, 1-17.
- Patole, P. B., & Kulkarni, V. V. (2017a). Experimental Investigation and Analysis of Effect of Process Parameters on Surface Roughness of AISI 4340 during MQL Turning with Nano Fluid. Manufacturing Technology Today, 16(7), 11-20.
- Patole, P. B., & Kulkarni, V. V. (2017b). Experimental Investigation and Optimization of Cutting Parameters with Multi Response Characteristics in MQL Turning of AISI 4340 using Nano Fluid. Journal of Cogent Engineering, 4(1), 1-14.
- Patole, P. B., & Kulkarni, V. V. (2018). Prediction of Surface Roughness and Cutting Force under MQL Turning of AISI 4340 with Nano Fluid by using Response Surface Methodology. Journal of Manufacturing Review, 5, 2018.
- Singh, C. S., Amrit Pal & Singh, T. (2016). Performance Evaluation of Aluminium 6063 Drilling under the Influence of Nano fluid Minimum Quantity Lubrication. Journal of Cleaner Production, 137, 537-545.
- Sripathi, P. S. (2009). Investigation into the Effects of Tool Geometry and Metal Working Fluids on Tool Forces and Tool Surfaces during Orthogonal Tube Turning of Aluminum 6061 Alloy.
- Suhail, A. H., Ismail, N., Wong, S. V., and Jalil, A. N. A. (2010). Team Mechanics Materials and High Speed Machining, Optimization of Cutting Parameters of Turning Operations by using Geometric Programming. American Journal of Engineering and Applied sciences, 3(1), 102-108.
- Vinay, V., Ramesh, M. R., & Chakradhar, D. (2018). Experimental Investigation and Optimization of Machining Parameters for Sustainable Machining. Journal of Materials and Manufacturing Processes, 33, 1782-1792.
Abstract Views: 236
PDF Views: 0