Manufacturing Technology Today

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Effect of Hardness and Tensile Behaviour of Al-2024/TiB2 Coated B4C Particles Synthesized by Stir Casting Route


Affiliations
1 Presidency University, Itgalpura, Rajanukunte, Bengaluru, India
2 Sir M.V. Institute of Technology, Bengaluru, India
3 Desmaco Engineering Services Pvt. Ltd, Bengaluru, India
     

   Subscribe/Renew Journal


Nowadays the production of light weight, low cost and high performance aluminium based composites has undergone significant evolution. In this work, Boron Carbide (B4C) were introduced into Al-2024 alloy produced by stir casting method. The B4C particles is coated with TiB2 via sol-gel process and reinforced in Al-2024 alloy by stir casting process to produce composite. Stir casting technique is gaining importance due to its easy setup, low cost, uniform dispersion of reinforcement compare to other techniques. Metal Matrix Composite is stir casted by incorporation of B4C reinforcements by varying 2%, 4%,6%, 8% and 10 wt% to investigate mechanical properties. Hardness, porosity and tensile behavior of alloy and composites were evaluated and found that both hardness and tensile strength increases with increases in percentage of reinforcement. On the other hand a slight increasing amount of porosity is observed with increasing the B4C particles of the composites. Microstructure of tensile fractured surface of Al-2024/B4Cp composites indicates that the presence of intact reinforcement B4C particles on the fracture surface and bonding between boron carbide and aluminum was superior indicating that deformation caused due to ductile behavior.

Keywords

Al-2024, Hardness, Porosity, Tensile, Tensile Fracture.
User
Subscription Login to verify subscription
Notifications
Font Size

  • Ashok Kumar, V., Anil, M. P., Rajesh, G. L., Hiremath, V., & Auradi, V. (2018). Tensile and Compression Behaviour of Boron Carbide Reinforced 6061Al MMC’s processed through Conventional Melt Stirring. Materials Today proceedings, 5(8), Part 3, 16141-16145.

  • Auradi, V., Rajesh, G. L, & Kori, S. A. (2014). Processing of B4C Particulate Reinforced 6061 Aluminum Matrix Composites by melt stirring involving two-step addition. Procedia Materials Science, 6, 1068 -1076.

  • Chen, H. S., Wang, W. X., Nie, H. H., Zhou, J., & Zhang, P. (2018). Microstructure evolution and mechanical properties of B4C/6061Al neutron absorber composite sheets fabricated by powder metallurgy. Journal of Alloys and Compounds, 730, 342-351.

  • Nie, C-Z, Gu, J-J, Liu, J-L and Zhang, D. (2007). Production of Boron Carbide Reinforced 2024 Aluminum Matrix Composites by Mechanical Alloying. Materials Transactions, 48(5), 990 to 995.

  • Dasgupta, R. (2012). Aluminium alloy –based metal matrix composites: a potential material for wear resistance applications. International Scholarly Research Notices, 2012, 1-14. Article ID 594573

  • Dhanashekar, M., & Senthil Kumar, V. S. (2014). Squeeze Casting of Aluminium Metal Matrix Composites- An Overview. Procedia Engineering, 97, 412 – 420.

  • Gudipudi, S., Nagamuthu, S., SubbuSubbian, K., & Chilakalapalli, S. P. R. (2020). Enhanced mechanical properties of AA6061-B4C composites developed by a novel ultra-sonic assisted stir casting. Engineering Science and Technology: An International Journal, 23(5), 1233-1243.

  • Kalaiselvan, K., Murugan, N., & Parameswaran, S. (2011). Production and Characterization of AA6061-B4C Stir cast composite. Materials & Design, 32(7), 4004-4009.

  • Lokesh, G. N., & Karunakara, S. (2020). Impact of Particle Size Distribution for Variable Mixing Time on Mechanical Properties and Microstructural Evaluation of Al-Cu/B4C Composite. Materials Today: Proceedings, 22, 1715–1722.

  • Lokesh, G. N., Ramachandra, M., Mahendra, K. V., & Sreenith, T. (2013). Characterization of Al-Cu alloy reinforced fly ash metal matrix composites by squeeze casting method. International Journal of Engineering, Science and Technology, 5(4), 71-79.

  • Lokesh, G. N., Ramachandra, M., & Mahendra, K. V. (2014). Tensile and wear behaviour of Al-4.5%Cu alloy reinforced fly ash/SiC by stir and squeeze casting with rolled composites. International Journal on Mechanical Engineering and Robotics, 2(3), 10-15.

  • Lokesh, G. N., Ramachandra, M., & Mahendra, K. V. (2018). Mechanical and dry sliding wear behaviour of hot rolled hybrid composites produced by direct squeeze casting method. Materials Today: Proceedings, 5(1), Part 3, 2597-2604.

  • Mahendra, K. V., & Radhakrishna, K. (2007). Fabrication of Al–4.5% Cu alloy with fly ash metal matrix composites and its characterization. Materials Science-Poland, 25(1), 57-68.

  • Mahesh Kumar, V., & Venkatesh, C. V. (2018). Effect of ceramic reinforcement on mechanical properties of aluminum matrix composites produced by stir casting process. Materials Today: Proceedings, 5(1), Part 3, 2466-2473.

  • Manjunatha, B., Niranjan, H. B., & Satyanarayana, K. G. (2015). Effect of mechanical and thermal loading on boron carbide particles reinforced Al-6061 alloy. Materials Science and Engineering: A, 632, 147-155.

  • Mazaheri, Y., Meratian, M., Emadi, R., & Najarian, A. R. (2013). Comparison of microstructural and mechanical properties of Al–TiC, Al–B4C and Al–TiC–B4C composites prepared by casting techniques. Materials Science and Engineering: A, 560, 278-287.

  • Mazahery, A., Shabani, M. O., Rahimipour, M. R., Tofigh, A. A., & Razavi, M. (2012). Effect of coated B4C reinforcement on mechanical properties of squeeze cast A356 composites. Kovove Materialy, 50(2) , 107–113.

  • Mohammad Sharifi, E., Karimzadeh, F., & Enayati, M. H. (2011). Fabrication and evaluation of mechanical and tribological properties of boron carbide reinforced aluminum matrix nanocomposites. Materials and Design, 32, 3263–3271.

  • Pozdniakov, A. V., Lotfy, A., Qadir, A., Shalaby, E., Khomutov, M. G., Churyumov, A. Yu., & Zolotorevskiy, V. S. (2017). Development of Al-5Cu/B4C composites with low coefficient of thermal expansion for automotive application. Materials Science and Engineering: A, 688, 1-8.

  • Ravi, B., Balu Naik, B., & Udaya Prakash, J. (2015). Characterization of Aluminium Matrix Composites (AA6061/B4C) Fabricated by Stir Casting Technique. Materials Today: Proceedings, 2(4-5), 2984-2990.

  • Sanjay, S. J., Shashidar K. Naik, & Shashishekar, C. (2017). Effect of Artificial Ageing on Wear Behaviour of Al7010/B4C Composite. Materials Today: Proceedings, 4(10), 11194-11200.

  • Sarikaya, O., Anik, S., Aslanlar, S., Okumus, S. C., & Celik, E. (2007). Al–Si/B4C composite coatings on Al–Si substrate by plasma spray technique. Materials & Design, 28(9), 2443-2449.

  • Tariq, N. H., Gyansah, L., Wang, J. Q., Qiu, X., & Xiong, T. Y. (2018). Cold spray additive manufacturing: A viable strategy to fabricate thick B4C/Al composite coatings for neutron shielding applications. Surface and Coatings Technology, 339, 224-236.

  • Vijaya Kumar Raju, P., Rajesh, S., Babu Rao, J., & Bhargava, N. R. M. R. (2018). Tribological behavior of Al-Cu alloys and innovative Al-Cu metal matrix composite fabricated using stir-casting technique. Materials Today Proceedings, 5(1), Part 1, 885-896.

  • Wang, Z., Song, M., Sun, C., & He, Y. (2011). Effects of particle size and distribution on the mechanical properties of SiC reinforced Al–Cu alloy composites. Materials Science and Engineering – A, 528, 1131–1137.


Abstract Views: 233

PDF Views: 0




  • Effect of Hardness and Tensile Behaviour of Al-2024/TiB2 Coated B4C Particles Synthesized by Stir Casting Route

Abstract Views: 233  |  PDF Views: 0

Authors

G. N. Lokesh
Presidency University, Itgalpura, Rajanukunte, Bengaluru, India
S. Shivakumar
Sir M.V. Institute of Technology, Bengaluru, India
B. G. Rohit
Desmaco Engineering Services Pvt. Ltd, Bengaluru, India
T. R. Preetham
Desmaco Engineering Services Pvt. Ltd, Bengaluru, India

Abstract


Nowadays the production of light weight, low cost and high performance aluminium based composites has undergone significant evolution. In this work, Boron Carbide (B4C) were introduced into Al-2024 alloy produced by stir casting method. The B4C particles is coated with TiB2 via sol-gel process and reinforced in Al-2024 alloy by stir casting process to produce composite. Stir casting technique is gaining importance due to its easy setup, low cost, uniform dispersion of reinforcement compare to other techniques. Metal Matrix Composite is stir casted by incorporation of B4C reinforcements by varying 2%, 4%,6%, 8% and 10 wt% to investigate mechanical properties. Hardness, porosity and tensile behavior of alloy and composites were evaluated and found that both hardness and tensile strength increases with increases in percentage of reinforcement. On the other hand a slight increasing amount of porosity is observed with increasing the B4C particles of the composites. Microstructure of tensile fractured surface of Al-2024/B4Cp composites indicates that the presence of intact reinforcement B4C particles on the fracture surface and bonding between boron carbide and aluminum was superior indicating that deformation caused due to ductile behavior.

Keywords


Al-2024, Hardness, Porosity, Tensile, Tensile Fracture.

References