Indian Journal of Fibre & Textile Research

Open Access Open Access  Restricted Access Subscription Access

Parameters Affecting Needle Thread Tension during Lockstitch Process


Affiliations
1 Department of Textile Technology, Dr BR Ambedkar National Institute of Technology, Jalandhar 144 011, India
 

Role of check spring and parameters, like fabric compressibility, feed rate, breaking elongation percentage of thread and needle thread pre-tension, on the thread tension profile and peak tension values of needle thread has been studied during the stitching cycle. Needle thread tension is measured at two different locations, viz Zone 1 and Zone 2. Zone 1 lies between guide element 1 and guide element 2, while Zone 2 lies between guide element 3 and needle bar. It is observed that the values of thread tension peaks developed in Zone 1 is higher than those developed in Zone 2. It is also observed that in a full cycle of a stitch forming process, tension profile of needle thread has four peaks, out of which tension peaks 1 and 3 occur due to the action of check spring and these two peaks almost vanishes on removal of check spring. The effect of different parameters on needle thread tension profile and its peak values are studied in Zone 1. It is found that the major tension peak values of needle thread reduces with the increase in fabric compressibility and thread extensibility but increases with the increase in feed rate and needle thread pre-tension.

Keywords

Check Spring, Denim, Fabric Compressibility, Feed Rate, Lockstitch Process, Nonwoven, Needle Thread Tension, Peak Tension, Rib Knitted Fabric, Sewing Thread, Thread Elongation.
User
Notifications
Font Size

  • Ferreira F B N, Harlock SC & Grosberg P, Int J Clothing Sci Technol, 6(5) (1994) 26.

  • Hayes S G, Res J Text Apparel, 5(2) (2001) 54.

  • Kamata Y, Sakai T, Onoue M & Chatani Y, J Text Mach Soc Japan, 39(1) (1986) 7.

  • Lojen D Z & Gersak J, Indian J Clothing Sci Technol, 13(¾) (2001) 240.

  • Lojen D Z & Gersak J, Text Res J, 75(6) (2001) 498.

  • Onoue M, J Soc Fibre Sci Technol, Japan, 10 (1984) 395.

  • Koncer P, Gurarda A, Kaplangiray B & Kanik M, Tekstil, 24(1) (2013) 118.

  • Rengasamy R S & Wesley D S, Autex Res J, 11(1) (2011) 1.

  • Rengasamy R S & Wesley D S, Fibers Polym, 15(18) (2014) 1766.

  • Rengasamy R S & Wesley D S, Fibers Polym, 15(18) (2014) 1773.

  • Debnath S & Madhusoothanan M, J Eng Fibre Fabric, 4(4) (2009). doi: 10.1177/155892500900400404

  • Standard Test Method for Tensile Properties of Yarns by the Single-Strand Method, ASTM D2256/D2256M – 10, Annual Book of ASTM Standards (ASTM, USA), 2015.

  • Kamata Y, Sakai T, Onoue M & Chatani Y, J Text Mach Soc Japan, 39(6) (1986) 31.

  • Chauhan R & Ghosh S, Indian J Fibre Text Res, 45(4) (2020) 411.

  • Chauhan R & Ghosh S, J Text Inst, (2021). doi:10.1080/ 00405000.2021.1872837.

  • Boubaker J, Sana A & Faouzi K, Indian J Fibre Text Res, 42 (2017) 325.


Abstract Views: 179

PDF Views: 104




  • Parameters Affecting Needle Thread Tension during Lockstitch Process

Abstract Views: 179  |  PDF Views: 104

Authors

Roopam Chauhan
Department of Textile Technology, Dr BR Ambedkar National Institute of Technology, Jalandhar 144 011, India
Subrata Ghosh
Department of Textile Technology, Dr BR Ambedkar National Institute of Technology, Jalandhar 144 011, India

Abstract


Role of check spring and parameters, like fabric compressibility, feed rate, breaking elongation percentage of thread and needle thread pre-tension, on the thread tension profile and peak tension values of needle thread has been studied during the stitching cycle. Needle thread tension is measured at two different locations, viz Zone 1 and Zone 2. Zone 1 lies between guide element 1 and guide element 2, while Zone 2 lies between guide element 3 and needle bar. It is observed that the values of thread tension peaks developed in Zone 1 is higher than those developed in Zone 2. It is also observed that in a full cycle of a stitch forming process, tension profile of needle thread has four peaks, out of which tension peaks 1 and 3 occur due to the action of check spring and these two peaks almost vanishes on removal of check spring. The effect of different parameters on needle thread tension profile and its peak values are studied in Zone 1. It is found that the major tension peak values of needle thread reduces with the increase in fabric compressibility and thread extensibility but increases with the increase in feed rate and needle thread pre-tension.

Keywords


Check Spring, Denim, Fabric Compressibility, Feed Rate, Lockstitch Process, Nonwoven, Needle Thread Tension, Peak Tension, Rib Knitted Fabric, Sewing Thread, Thread Elongation.

References