Indian Journal of Chemical Technology

Open Access Open Access  Restricted Access Subscription Access

Effect of Electroplating Time on Microstructure, Corrosion and Wear Behaviour of Ni-P-W-TiO2 Coating


Affiliations
1 Department of Materials Engineering, Faculty of Mechanical and Materials Engineering, Graduate University of Advanced Technology, 7631133131, Kerman, Iran, Islamic Republic of
 

Ni-P-W-TiO<sub>2</sub> coating has been deposited on the AISI 304L steel substrate using the electroplating method. Electroplating has been performed at 30, 45, and 60 min, and the effect of electroplating time on microstructure, corrosion and wear behaviour has been investigated. The coatings have been characterized by use of scanning electron microscopy (SEM). In order to investigate corrosion resistance, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) tests have been used in 3.5% of NaCl aqueous solution. A pin on disk test has been used to test the wear resistance of uncoated and coated samples. Sample micro-hardness has also been measured by the Vickers hardness test. Examination of the microstructure has shown that the best time for deposition is 45 min. The results of potentiodynamic polarization and electrochemical impedance spectroscopy tests are also consistent with microscopic images, and the results have shown that the coating created within 45 min has the highest corrosion resistance (7058 Ω.cm<sup>2</sup>) compared to coated sample within 30 (4142 Ω.cm<sup>2</sup>) and 60 (3059 Ω.cm<sup>2</sup>) minutes. Also, the results of the wear test and micro-hardness have shown that composite coating formed within 45 minutes has the highest wear resistance and micro-hardness (677 Vickers) compared to coated sample within 30 (257 Vickers) and 60 (638 Vickers) minutes.


Keywords

Ni-P-W-TIO2 Coating, Electroplating Time, Potentiodynamic Polarization, Electrochemical Impedance Spectroscopy, Wear Resistance.
User
Notifications
Font Size

  • Keong K G & Sha W, Surf Coat Technol, 168 (2003) 263.

  • Ebrahimifar H, Zandrahimi M, Nikrooz B & Sedighi M, Indian J Chem Technol, 20 (2012) 40.

  • Varmaziar S, Atapour M & Hedberg Y S, Mater Degrad, 6 (2022) 1.

  • Zandrahimi M, Vatandoost J & Ebrahimifar H, Oxid Met, 76 (2011) 347.

  • Limooei M B, Ebrahimifar H & Hosseini S, Indian J Eng Mater Sci, 20 (2013) 513.

  • Rajabi T, Atapour M, Elmkhah H & Nahvi S M, Thin Solid Films, 753 (2022) 139288.

  • Mosavi A & Ebrahimifar H, Int J Hydrogen Energy, 45 (2020) 3145.

  • Wang S C & Wei W C J, Mater Chem Phys, 78 (2003) 574.

  • Ebrahimifar H, Oxid Met, 91 (2019) 417.

  • Gul H, Kilic F, Usal M, Aslan S, Apl A & Akbulut H, Appl Surf Sci, 258 (2012) 4260.

  • Ebrahimifar H & Zandrahimi M, Bull Mater Sci, 40 (2017) 1273.

  • Li B, Li D, Chen W, Liu Y, Zhang J, Wei Y, Zhang W & Jia W, Ceram Int, 45 (2019) 4870.

  • Wang F, Chen L, Wang Y, Yao M, Hao S, Ouyang J & Huang Z, Ceram Int, 43 (2017) 2853.

  • Mortezanejad E, Atapour M, Salimijazi H, Alhaji A & Hakimizad A, J Mater Eng Perform, 30 (2021) 4030.

  • Tsuru Y, Nomura M & Foulkes F, J Appl Electrochem, 30 (2000) 231.

  • Garcia I, Conde A, Langelaan G, Fransaer J & Celis J P, Corros Sci, 45 (2003) 1173.

  • Ashassi-Sorkhabi H & Rafizadeh S H, Surf Coat Technol, 176 (2004) 318.

  • Sadreddini S & Afshar A, Appl Surf Sci, 303 (2014) 125.

  • Zhang X, Wang F & Du Y, Surf Coat Technol, 201 (2007) 7241.

  • Zhang S, Li Q, Yang X, Zhong X, Dai Y & Luo F, Mater Charact, 61 (2010) 269.

  • Sadeghi A, Khosroshahi R & Sadeghian Z, J Surf Invest XRay Synchrotron Neutron Tech, 5 (2011) 186.

  • Baghery P, Farzam M, Mousavi A & Hosseini M, Surf Coat Technol, 204 (2010) 3804.

  • Li Q, Yang X, Zhang L, Wang J & Chen B, J Alloys Comp, 482 (2009) 339.

  • Szczygiel B & Kolodziej M, T I Met Finish, 83 (2005) 181.

  • Fini M H & Amadeh A, T Nonferr Metal Soc China, 23 (2013) 2914.

  • Abdel-Gaber A, Abd-El-Nabey B, Sidahmed I, El-Zayady A & Saadawy M, Corros Sci, 48 (2006) 2765.

  • Srivastava M, Selvi V E, Grips V W & Rajam K, Surf Coat Technol, 201 (2006) 3051.

  • Amin M A, Khaled K, Mohsen Q & Arida H, Corros Sci, 52 (2010) 1684.

  • Saeidpour F, Zandrahimi M & Ebrahimifar H, Corros Sci, 153 (2019) 200.

  • Bajat J, Miskovic-Stankovic V, Popic J & Drazic D, Prog Org Coat, 63 (2008) 201.

  • Wang Y, Zhou Q, Li K, Zhong Q & Bui Q B, Ceram Int, 41 (2015) 79.

  • Song L, Wang Y, Lin W & Liu Q, Surf Coat Technol, 202 (2008) 5146.

  • Sadeghi S & Ebrahimifar, Indian J Eng Mater Sci, 29 (2022) 108.

  • Wang Y, Wang S J, Shu X, Gao W, Lu W & Yan B, J Alloys Compd, 617 (2014) 472.

  • Alirezaei S, Monirvaghefi S M, Salehi M, Saatchi A & Kargosha M, Surf Eng, 21 (2005) 60.

  • Staia M, Surf Coat Technol, 86 (1996) 598.

  • Sadeghi S & Ebrahimifar, Int J Mater Res, 112 (2020) 474.

  • Gadhari P & Sahoo P, Mater Today Proceedings, 2 (2015) 2367.

  • Moshrefifar M, Ebrahimifar & Hakimizad A, Coatings, 12 (2022) 1438.

  • Palaniappa M & Seshadri S, Wear, 265 (2008) 735.


Abstract Views: 128

PDF Views: 95




  • Effect of Electroplating Time on Microstructure, Corrosion and Wear Behaviour of Ni-P-W-TiO2 Coating

Abstract Views: 128  |  PDF Views: 95

Authors

Sajjad Sadeghi
Department of Materials Engineering, Faculty of Mechanical and Materials Engineering, Graduate University of Advanced Technology, 7631133131, Kerman, Iran, Islamic Republic of
Hadi Ebrahimifar
Department of Materials Engineering, Faculty of Mechanical and Materials Engineering, Graduate University of Advanced Technology, 7631133131, Kerman, Iran, Islamic Republic of

Abstract


Ni-P-W-TiO<sub>2</sub> coating has been deposited on the AISI 304L steel substrate using the electroplating method. Electroplating has been performed at 30, 45, and 60 min, and the effect of electroplating time on microstructure, corrosion and wear behaviour has been investigated. The coatings have been characterized by use of scanning electron microscopy (SEM). In order to investigate corrosion resistance, potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) tests have been used in 3.5% of NaCl aqueous solution. A pin on disk test has been used to test the wear resistance of uncoated and coated samples. Sample micro-hardness has also been measured by the Vickers hardness test. Examination of the microstructure has shown that the best time for deposition is 45 min. The results of potentiodynamic polarization and electrochemical impedance spectroscopy tests are also consistent with microscopic images, and the results have shown that the coating created within 45 min has the highest corrosion resistance (7058 Ω.cm<sup>2</sup>) compared to coated sample within 30 (4142 Ω.cm<sup>2</sup>) and 60 (3059 Ω.cm<sup>2</sup>) minutes. Also, the results of the wear test and micro-hardness have shown that composite coating formed within 45 minutes has the highest wear resistance and micro-hardness (677 Vickers) compared to coated sample within 30 (257 Vickers) and 60 (638 Vickers) minutes.


Keywords


Ni-P-W-TIO2 Coating, Electroplating Time, Potentiodynamic Polarization, Electrochemical Impedance Spectroscopy, Wear Resistance.

References