Current Science

Open Access Open Access  Restricted Access Subscription Access

Experimental Analysis of the Ratio of Similar Materials by Similarity Model Test on Raw Coal


Affiliations
1 School of Energy Science and Engineering, Henan Polytechnic University, Jiaozuo, Henan 454003, China
2 Applied Technical College, China University of Mining and Technology, Xuzhou, Jiangsu 221008, China
3 State Key Laboratory for Coal Mine Disaster Dynamics and Control, Chongqing University, Chongqing 400044, China
 

Similarity model test is an effective approach to study the mechanism of hydraulic fracture propagation in coalbed methane reservoirs as well as theoretical analysis and numerical simulation. The efficiency of the similarity model test result is closely related to the selection and ratio of similar materials. Similar material ratio test was conducted to simulate the mechanical parameters of raw coal using orthogonal method and an appropriate similarity model for hydraulic fracturing experiment was developed in this study. Results show that it is suitable to select cement, gypsum as binder and apply pulverized coal as aggregate through the analysis of experimental data. The mechanical parameters of similar materials, including uniaxial compressive strength, elastic modulus, Poisson ratio and firmness coefficient are tested using laboratory tests. The impact of diverse ratios of similar materials on the mechanical parameters is analysed. A proper ratio is selected to make the mechanical parameters of raw coal close to the ones of similar material, in order to meet the demand of the similarity model test based on raw coal. The results can provide theoretical basis and technical support for the selection of similar materials to carry out hydraulic fracturing experiments.

Keywords

Experimental Investigation, Hydraulic Fracturing, Raw Coal, Similar Materials, Mechanical Parameters.
User
Notifications
Font Size

  • Shikuo, C., Tianhong, Y., Ranjith, P. G. and Chenhui, W., Mechanism of the two-phase flow model for water and gas based on adsorption and desorption in fractured coal and rock. Rock Mech. Rock Eng., 2017, 50, 571–586.

  • Dehghan, A. N., Goshtasbi, K., Ahangari, K., Jin, Y. and Bahmani, A., 3D numerical modeling of the propagation of hydraulic fracture at its intersection with natural (pre-existing) fracture. Rock Mech. Rock Eng., 2017, 50, 367–386.

  • Tiankui, G., Zhang, S., Zhanqing, Q., Tong, Z., Yongshun, X. and Jun, G., Experimental study of hydraulic fracturing for shale by stimulated reservoir volume. Fuel, 2014, 128, 373–380.

  • He, Q., Suorineni, F. T. and Oh, J., Review of hydraulic fracturing for preconditioning in cave mining. Rock Mech. Rock Eng., 2016, 49(12), 4893–4910.

  • Shangyu, Y., Xingru, W., Lihong, H., Jianjun, W. and Yaorong, F., Migration of variable density proppant particles in hydraulic fracture in coal-bed methane reservoir. J. Nat. Gas Sci. Eng., 2016, 36, 662–668.

  • Yiyu, L., Liang, C., Zhaolong, G., Binwei, X., Qian, L. and Jiufu, C., Analysis on the initial cracking parameters of cross-measure hydraulic fracture in underground coal mines. Energies, 2015, 8(7), 6977–6994.

  • Bingxiang, H., Changyou, L., Junhui, F. and Hui, G., Hydraulic fracturing after water pressure control blasting for increased fracturing. Int. J. Rock Mech. Min. Sci., 2011, 48, 976–983.

  • Wang, Y., Li, X. and Zhang, B., Analysis of fracturing network evolution behaviors in random naturally fractured rock blocks. Rock Mech. Rock Eng., 2016, 49, 4339–4347.

  • Jian, Z., Mian, C., Yan, J. and Guangqing, Z., Analysis of fracture propagation behavior and fracture geometry using a tri-axial fracturing system in naturally fractured reservoirs. Int. J. Rock Mech. Min, Sci., 2008, 45, 1143–1152.

  • Guo, C. H., Xu, J. C., Wei, M. Z. and Jiang, R. Z., Experimental study and numerical simulation of hydraulic fracturing tight sandstone reservoirs. Fuel, 2015, 159, 334–344.

  • Estrada, J. M. and Rao, B., A review of the issues and treatment options for wastewater from shale gas extraction by hydraulic fracturing. Fuel, 2016, 182, 292–303.

  • Jianpeng, Z., Weizhong, C., Jingqiang, Y., Diansen, Y. and Jianping, Y., 3-D numerical simulation of hydraulic fracturing in a CBM reservoir. J. Nat. Gas Sci. Eng., 2017, 37, 386–396.

  • Kui, L., Deli, G., Yanbin, W. and Yuanchao, Y., Effect of local loads on shale gas well integrity during hydraulic fracturing process. J. Nat. Gas Sci. Eng., 2017, 37, 291–302.

  • Xie, L. M., Min, K.-B. and Shen, B. T., Simulation of hydraulic fracturing and its interactions with a preexisting fracture using displacement discontinuity method. J. Nat. Gas Sci. Eng., 2016, 36, 1284–1294.

  • Zhipeng, X., Zhiye, Z., Jianping, S. and Ming, L., Determination of hydraulic conductivity of fractured rock masses: a case study for a rock cavern project in Singapore. J. Rock Mech. Geotech. Eng., 2015, 7, 178–184.

  • Dazhao, S., Zhentang, L., Enyuan, W., Limin, Q., Qinqing, G. and Zhaoyong, X., Evaluation of coal seam hydraulic fracturing using the direct current method. Int. J. Rock Mech. Min. Sci., 2015, 78, 230–239.

  • Huiying, T., Winterfeld Philip, H., Yushu, W., Zhaoqin, H., Yuan, D., Zhengfu, P. and Juncheng, Z., Integrated simulation of multistage hydraulic fracturing in unconventional reservoirs. J. Nat. Gas Sci. Eng., 2016, 36, 875–892.

  • Xiao, L., Haixiao, L. and Fan, Z., Study on ratio of similar materials based on coal mass strength. Comput. Modell. New Technol., 2014, 18(12), 336–340.

  • Wenyan, Z., Mohamed, Z. and Yukio, H., Influence of aggregate materials characteristics on the drying shrinkage properties of mortar and concrete. Const. Build. Mater., 2013, 49, 500–510.


Abstract Views: 307

PDF Views: 114




  • Experimental Analysis of the Ratio of Similar Materials by Similarity Model Test on Raw Coal

Abstract Views: 307  |  PDF Views: 114

Authors

Fan Zhang
School of Energy Science and Engineering, Henan Polytechnic University, Jiaozuo, Henan 454003, China
Geng Ma
School of Energy Science and Engineering, Henan Polytechnic University, Jiaozuo, Henan 454003, China
Xiao Liu
School of Energy Science and Engineering, Henan Polytechnic University, Jiaozuo, Henan 454003, China
Yunqi Tao
School of Energy Science and Engineering, Henan Polytechnic University, Jiaozuo, Henan 454003, China
Rui Li
Applied Technical College, China University of Mining and Technology, Xuzhou, Jiangsu 221008, China
Dan Feng
State Key Laboratory for Coal Mine Disaster Dynamics and Control, Chongqing University, Chongqing 400044, China

Abstract


Similarity model test is an effective approach to study the mechanism of hydraulic fracture propagation in coalbed methane reservoirs as well as theoretical analysis and numerical simulation. The efficiency of the similarity model test result is closely related to the selection and ratio of similar materials. Similar material ratio test was conducted to simulate the mechanical parameters of raw coal using orthogonal method and an appropriate similarity model for hydraulic fracturing experiment was developed in this study. Results show that it is suitable to select cement, gypsum as binder and apply pulverized coal as aggregate through the analysis of experimental data. The mechanical parameters of similar materials, including uniaxial compressive strength, elastic modulus, Poisson ratio and firmness coefficient are tested using laboratory tests. The impact of diverse ratios of similar materials on the mechanical parameters is analysed. A proper ratio is selected to make the mechanical parameters of raw coal close to the ones of similar material, in order to meet the demand of the similarity model test based on raw coal. The results can provide theoretical basis and technical support for the selection of similar materials to carry out hydraulic fracturing experiments.

Keywords


Experimental Investigation, Hydraulic Fracturing, Raw Coal, Similar Materials, Mechanical Parameters.

References





DOI: https://doi.org/10.18520/cs%2Fv113%2Fi11%2F2174-2179