Current Science

Open Access Open Access  Restricted Access Subscription Access

Dynamic Modelling and Parameter Identification for Cable-Driven Manipulator


Affiliations
1 College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
2 State Key Laboratory of Fluid Power and Mechatronic Systems, Zhejiang University, Hangzhou 310027, China
 

Cable-driven manipulators (CDMs) have several advantages, but unknown dynamic characters restrict their control performance. The motors of CDMs are placed at the base and power is transmitted by cables between the motors and driving pulleys. These cables interact with the links of the manipulator, which poses a challenge for obtaining the dynamic model. In this study, the interaction between cables and manipulators is analysed, and a dynamic model is derived based on Newton–Euler method. To eliminate excessive variance in recursive equations, the impact of pretension force is considered and some equivalent assumptions are proposed. To improve the accuracy of parameter identification, limited terms of Fourier series are adopted for the identification trajectory. Considering various limitations of CDMs, such as maximum joint angle, speed and acceleration, artificial bee colony algorithm is used to optimize the coefficients of the identification trajectory. Simulations verify that the dynamic model can precisely calculate the driving torque of CDMs. Moreover, parameter identification experiment affirms the efficiency of the proposed parameter identification method.

Keywords

Artificial Bee Colony Algorithm, Cable-Driven Manipulator, Dynamics, Parameter Identification.
User
Notifications
Font Size

  • Shang, W. et al., Synchronization control in the cable space for cable-driven parallel robots. IEEE Trans. Ind. Electron., 2018, 66(6), 4544–4554; doi:10.1109/TIE.2018.2864512.

  • Zhang, N., Shang, W. W. and Cong, S., Geometry-based trajectory planning of a 3–3 cable-suspended parallel robot. IEEE Trans. Robot., 2017, 33(2), 484–491.

  • Wang, Y. et al., Practical tracking control of robot manipulators with continuous fractional-order nonsingular terminal sliding mode. IEEE Trans. Ind. Electron., 2016, 63(10), 6194–6204.

  • Wang, Y. et al., A new adaptive time-delay control scheme for cabledriven manipulators. IEEE Trans. Ind. Inform., doi:10.1109/TII.2018.2876605.

  • Wang, Y. et al., Practical adaptive fractional-order nonsingular terminal sliding mode control for a cable-driven manipulator. Int. J. Robust Nonlinear Control, 2019, 29(5), 1396–1417; doi: 10.1002/rnc.4441.

  • Wang, Y. et al., Adaptive super-twisting fractional-order nonsingular terminal sliding mode control of cable-driven manipulators. ISA Trans., 2019, 86, 163–180; doi:10.1016/j.isatra.2018.11.009.

  • Wang, Y. et al., Trajectory tracking control of underwater vehiclemanipulator system using discrete time delay estimation. IEEE Access, 2017, 5, 7435–7443; doi:10.1109/ACCESS.2017.2701350.

  • Du, J. et al., Jacobian analysis of a long-span cable-driven manipulator and its application to forward solution. Mech. Mach. Theory, 2010, 45(9), 1227–1238.

  • Duan, X. et al., Calibration and motion control of a cable-driven parallel manipulator based triple-level spatial positioner. Adv. Mech. Eng., 2014, 6, 1–10.

  • Tzemanaki, A. et al., Design of a multi-DOF cable-driven mechanism of a miniature serial manipulator for robot-assisted minimally invasive surgery. In IEEE International Conference Biomedical Robotics and Biomechatronics, Singapore, 2016, pp. 55–60.

  • Gonzalez-Rodriguez, A. et al., On the effects of the design of cable-driven robots on kinematics and dynamics models accuracy. Mechatronics, 2017, 43, 18–27.

  • Xue, R. et al., A cable-pulley system modeling based position compensation control for a laparoscope surgical robot. Mech. Mach. Theory, 2017, 118, 283–299.

  • Gungor, G. et al., Online estimation and compensation of friction in industrial cable robot manipulation. IFAC-PapersOnLine, 2015, 48(3), 1332–1337.

  • Grossard, M. and Fichera, F., Polynomial piece-wise stiffness in cable-based transmissions for robots: modeling and identification. IFAC-PapersOnLine, 2017, 50(1), 14581–14587.

  • Fichera, F. and Grossard, M., On the modeling and identification of stiffness in cable-based mechanical transmissions for robot manipulators. Mech. Mach. Theory, 2017, 108, 176–190.

  • Yu, L. et al., Dynamical model and experimental identification of a cable-driven finger joint for surgical robot. In IEEE International Conference Mechanical Automation, Takamatsu, Japan, 2017; doi:10.1109/ICMA.2017.8015860.

  • Qi, Z., Wang, J. and Wang, G., An efficient model for dynamic analysis and simulation of cable–pulley systems with time-varying cable lengths. Mech. Mach. Theory, 2017, 116, 383–403.

  • Zhang, N. and Shang, W., Dynamic trajectory planning of a 3DOF under-constrained cable-driven parallel robot. Mech. Mach. Theory, 2016, 98, 21–35.

  • Ismail, M., Lahouar, S. and Romdhane, L., Collision-free and dynamically feasible trajectory of a hybrid cable–serial robot with two passive links. Robot. Auton. Syst., 2016, 80, 24–33.

  • Yuan, M. et al., An improved on-line trajectory planner with stability-guaranteed critical test curve algorithm for generalized parametric constraints. IEEE/ASME Trans. Mechatron., 2018, 23(5), 2459–2469.

  • Zhou, J. P., Zhong, Z. D. and Wang, Z. Z., Motion trajectory planning of 3-dof wire-driven parallel robot. Adv. Mater. Res., 2012, 424, 369–372.

  • Ismail, M., Samir, L. and Romdhane, L., Dynamic in path planning of a cable driven robot. Design Model. Mech. Syst., 2013.

  • Pinto, A. M. et al., A cable-driven robot for architectural constructions: a visual-guided approach for motion control and pathplanning. Auton. Robots, 2017, 41(7), 1–13.

  • Lahouar, S. et al., Collision free path-planning for cable-driven parallel robots. Robotics Autonom, Syst., 2009, 57(11), 1083–1093.

  • Tang, L. et al., Dynamic trajectory planning study of planar twodof redundantly actuated cable-suspended parallel robots. Mechatronics, 2015, 30, 187–197.

  • Lau, D., Oetomo, D. and Halgamuge, S. K., Inverse dynamics of multilink cable-driven manipulators with consideration of joint interaction forces and moments. IEEE Trans. Robot., 2015, 31(2), 479–488.

  • Xuechao, D., Yuanying, Q. and Jingli, D., Dynamic analysis and vibration attenuation of cable-driven parallel manipulators for large workspace applications. Adv. Mech. Eng., 2013, 4, 1–6.

  • Nielsen, M. C. et al., Constrained multi-body dynamics for modular underwater robots – theory and experiments. Ocean Eng., 2018, 149, 358–372.

  • Meng, W. et al., Consensus control of nonlinear multiagent systems with time-varying state constraints. IEEE Trans. Cybern., 2017, 47(8), 2110–2120.

  • Meng, W. et al., Distributed control of high-order nonlinear input constrained multiagent systems using a backstepping-free method. IEEE Trans. Cybern., 2018, 99, 1–11; doi:10.1109/TCYB.2018.2853623.

  • Yuan, M. et al., Time optimal contouring control of industrial biaxial gantry: a highly efficient analytical solution of trajectory planning. IEEE/ASME Trans. Mechatron., 2017, 22(1), 247–257.

  • Deng, W., Yao, J. and Ma, D., Robust adaptive precision motion control of hydraulic actuators with valve dead-zone compensation. ISA Trans., 2017, 70, 269–278.

  • Deng, W., Yao, J. and Ma, D., Time-varying input delay compensation for nonlinear systems with additive disturbance: an output feedback approach. Int. J. Robust Nonlinear Control, 2018, 28(1), 31–52.

  • Chen, Z., Yao, B. and Wang, Q., Accurate motion control of linear motors with adaptive robust compensation of nonlinear electromagnetic field effect. IEEE/ASME Trans. Mechatron., 2013, 18(3), 1122–1129.

  • Chen, Z., Yao, B. and Wang, Q., μ -Synthesis based adaptive robust control of linear motor driven stages with high-frequency dynamics: a case study with comparative experiments. IEEE/ASME Trans. Mechatron., 2015, 20(3), 1482–1490.

  • Chen, Z., Pan, Y. J. and Gu, J., Integrated adaptive robust control for multilateral teleoperation systems under arbitrary time delays. Int. J. Robust Nonlinear Control, 2016, 26(12), 2708–2728.

  • Chen, J. et al., Research on fuzzy control of path tracking for underwater vehicle based on genetic algorithm optimization. Ocean Eng., 2018, 156, 217–223.

  • Kong, K. and Tomizuka, M., Proxy-based impedance control of a cable-driven assistive system for upper extremity rehabilitation. IFAC Proc. Vol., 2011, 44(1), 2871–2876.

  • Kong, K., Proxy-based impedance control of a cable-driven assistive system. Mechatronics, 2013, 23(1), 147–153.

  • Babaghasabha, R., Khosravi, M. A. and Taghirad, H. D., Adaptive robust control of fully-constrained cable driven parallel robots. Mechatronics, 2014, 25, 27–36.

  • Caverly, R. J. and Forbes, J. R., State estimator design for a single degree of freedom cable-actuated system. J. Franklin Inst., 2016, 353(18), 4845–4869.

  • Jung, Y. and Bae, J., An asymmetric cable-driven mechanism for force control of exoskeleton systems. Mechatronics, 2016, 40, 41–50.

  • Boehler, Q. et al., From modeling to control of a variable stiffness device based on a cable-driven tensegrity mechanism. Mech. Mach. Theory, 2017, 107, 1–12.

  • Wang, Y. et al., A new continuous fractional-order nonsingular terminal sliding mode control for cable-driven manipulators. Adv. Eng. Software, 2018, 119, 21–29.

  • Wang, Y. et al., Time delay control of cable-driven manipulators with adaptive fractional-order nonsingular terminal sliding mode. Adv. Eng. Software, 2018, 121, 13–25.

  • Wang, Y. et al., A new discrete time delay control of hydraulic manipulators. Proc. iMeche, Part I, 2017, 231(3), 168–177.

  • Wang, Y., Chen, B. and Wu, H., Joint space tracking control of underwater vehicle-manipulator systems using continuous nonsingular fast terminal sliding mode. Proc. Inst. Mech. Eng. Part M. J. Eng. Maritime Environ., 2018, 232(4), 448–458; doi:10.1177/1475090217742241.

  • Wang, Y., Chen, B. and Wu, H., Practical continuous fractionalorder nonsingular terminal sliding mode control of underwater hydraulic manipulators with valve deadband compensators. Proc. Inst. Mech. Eng. Part M, 2018; doi:10.1177/1475090217753900.

  • Jin, M., Lee, J. and Tsagarakis, N. G., Model-free robust adaptive control of humanoid robots with flexible joints. IEEE Trans. Indust. Electron., 2017, 64(2), 1706–1715.

  • Hartenberg, R. S. and Denavit, J., A kinematic notation for lower pair mechanisms based on matrices. J. Appl. Mech., 1955, 77(2), 215–221.

  • Xu, W. et al., Kinematic analysis of a newly designed cable-driven manipulator. Trans. Can. Soc. Mech. Eng., 2018, 42(2), 125–135.

  • Yan, F. et al., Time delay control of cable-driven manipulators with artificial bee colony algorithm. Trans. Can. Soc. Mech. Eng., 2018, 42(2), 177–186.


Abstract Views: 318

PDF Views: 113




  • Dynamic Modelling and Parameter Identification for Cable-Driven Manipulator

Abstract Views: 318  |  PDF Views: 113

Authors

Fei Yan
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
Yaoyao Wang
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
Feng Ju
State Key Laboratory of Fluid Power and Mechatronic Systems, Zhejiang University, Hangzhou 310027, China
Jiafeng Yao
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
Bai Chen
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China
Hongtao Wu
College of Mechanical and Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016, China

Abstract


Cable-driven manipulators (CDMs) have several advantages, but unknown dynamic characters restrict their control performance. The motors of CDMs are placed at the base and power is transmitted by cables between the motors and driving pulleys. These cables interact with the links of the manipulator, which poses a challenge for obtaining the dynamic model. In this study, the interaction between cables and manipulators is analysed, and a dynamic model is derived based on Newton–Euler method. To eliminate excessive variance in recursive equations, the impact of pretension force is considered and some equivalent assumptions are proposed. To improve the accuracy of parameter identification, limited terms of Fourier series are adopted for the identification trajectory. Considering various limitations of CDMs, such as maximum joint angle, speed and acceleration, artificial bee colony algorithm is used to optimize the coefficients of the identification trajectory. Simulations verify that the dynamic model can precisely calculate the driving torque of CDMs. Moreover, parameter identification experiment affirms the efficiency of the proposed parameter identification method.

Keywords


Artificial Bee Colony Algorithm, Cable-Driven Manipulator, Dynamics, Parameter Identification.

References





DOI: https://doi.org/10.18520/cs%2Fv116%2Fi8%2F1331-1345