Indian Welding Journal

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Microstructure, Mechanical and Corrosion Behaviour of AA7075 Aluminium Alloy Friction Stir Welds


Affiliations
1 Department of Mechanical Engineering, Raghu Institute of Technology, Visakhapatnam, India
2 Defence Metallurgical Research Laboratory, Hyderabad, India
3 Department of Metallurgical Engineering, Andhra University, Visakhapatnam, India
     

   Subscribe/Renew Journal


Friction stir welding (FSW) is emerging as an alternative technique for joining high strength aluminium alloys as it eliminates the problems during fusion welding. In this work, the effect of post weld treatments (PWHT), viz., peak aging (T6) and retrogression and reaging (RRA) on the microstructure, mechanical properties, pitting corrosion and stress corrosion cracking (SCC) resistance of AA7075 aluminium alloy friction stir welds has been studied. An attempt also has been made to change the chemical composition of the weld nugget by adding boron carbide (B4C) nano powder with the aid of the FSW. Hardness and tensile properties were found to be better in PWHT – T6. Pitting corrosion and SCC resistances were improved in PWHT-RRA condition with negligible loss of strength when compared to PWHT-T6. RRA promotes coarse precipitation of the equilibrium phase η in the grains and sub grain boundaries, while maintaining a fine distribution of η' in the grain interiors. The increased strength and hardness in the peak aged (T6) condition was attributed to the presence of semi-coherent intermediate η' (MgZn2). With the addition of B4C nano powder to the weld nugget, hardness, tensile properties, pitting corrosion resistance and SCC resistance were further improved significantly when compared to the unreinforced weld nugget. PWHT-RRA treatment on the welds with B4C nano powder addition resulted in improved hardness of weld nugget which is attributed to the uniform distribution of strengthening precipitates in the matrix and powder strengthening. Pitting corrosion resistance, Tensile strength and SCC resistance was improved significantly in B4C added welds after RRA treatment when compared to the same welds without B4C addition.

Keywords

Friction Stir Welding, FSW, AA7075 Aluminium Alloy, Pitting Corrosion, Stress Corrosion Cracking, Retrogression-Reaging, RRA, Boron Carbide (B4C).
User
Subscription Login to verify subscription
Notifications
Font Size

  • Sharma C, Dwivedi DK, Kumar P (2012); Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of AA7039 aluminum alloy, Mater Des, 36, pp.379-390.

  • Paglia CS, Buchheit RG (2008); A look in the corrosion of aluminum alloy Friction stir welds, Scr Mater, 58, pp.383-387.

  • Karaaslan A, Kaya I, Atapek H (2007); Effect of aging temperature and of retrogression treatment time on the microstructure and mechanical properties of alloy AA 7075, Metal Sci Heat Treat, 49, pp.9-10.

  • Venugopal T, Srinivasa Rao K, Prasad Rao K (2004); Studies on friction stir welded AA7075 aluminum alloy. Trans Indian Inst Metals, 57 (6), pp.659-663.

  • Rao K Srinivasa, Rao K Prasad. (2004); Pitting corrosion of heat-treatable aluminium alloys and welds: a review, Trans Indian Inst Met, 57 (6), pp.593-610.

  • Ranganatha R (2013); Multi-stage heat treatment of aluminum alloy AA7049. Trans Nonferrous Met Soc China, pp.1570-1575.

  • Su JQ, Nelson TW, Mishra R, Mahoney M (2003); Microstructural investigation of friction stir welded 7050- T651 aluminium, Acta Mater, 51(3), pp.713-729.

  • Hassan KhAA, Norma AF, Price DA, Prangnell PB (2003); Stability of nugget zone grain structures in high strength Al-alloy friction stir welds during solution treatment. Acta Mater, 51 (7), pp.1923-1936.

  • Sullivan A, Robson JD (2008); Microstructural properties of friction stir welded and post weld heated 7449 aluminum alloy thick plate. Mater Sci Eng (A), 478, pp.351-360.

  • Oliveira Jr AF, de Barros MC, Cardoso KR, Travessa DN (2004); The effect of RRA on the strength and SCC resistance on AA7050 and AA7150 aluminum alloys, Mater Sci Eng, 379 (A), pp.321-326.

  • Fuller CB, Mahoney MW, Calabrese M (2010); Evolution of microstructure and mechanical properties in naturally aged 7050 and 7075 Al friction stir welds, Mater Sci Eng, 527 (9), pp.2233-2240.

  • Bahrami M, Dehgani K, Givi MKB (2014); A novel approach to develop aluminum matrix nano composite employing friction stir welding technique, Mater Des, 53, pp.217-225.

  • Azimzadegan T, Khalaj GH, Kaykha MM. Heidari AR (2011); Ageing behavior of friction stir welding AA7075-T6 aluminum alloy, Comput Eng Syst Appl ,Vol. II, pp.183-187.

  • Choi DH, Kim Y-Il, Kim DU (2012); Effect of SiC particles on microstructure and mechanical property of friction stir processed AA6061-T4, Trans Nonferrous Metal Soc China, 22(3), pp.614-618.

  • Su JQ, Nelson TW, Sterling CJ (2005); Microstructure evolution during FSW/FSP of high strength aluminum alloys, Mater Sci Eng A, 405(1-2), pp.277-286.

  • Gan YX, Solomon D, Reinbolt M (2010); Friction stir processing of particle reinforced composite materials, Materials, 3(1), pp.329-350.

  • Ramesh R, Murugan N (2010); Microstructure and metallurgical properties of aluminium 7075 - T651 alloy/BC 4 % vol. surface composite by friction stir 4 processing, Adv Mater Manuf Charact, 3(1), pp.301-306.

  • Zaid HR, Hatab AM, Ibrahim AMA (2011); Properties enhancement of Al-Zn-Mg alloy by retrogression and re-aging heat treatment. J Min Metal, 47 (1), pp.31-35.

  • Kashani-Bozorg SF, Jazayeri K (2008); Formation of Al/B4C surface nano composite layers on 7075 Al alloy 4 employing friction stir processing. AIP Conf Proc, 1136 (1), pp.715-719.

  • Shafiei-Zarghani A. (2009); Microstructures and mechanical properties of Al/Al2O3 surface nano-composite layer produced by friction stir processing, Mater Sci Eng A, 500, pp.84-91.


Abstract Views: 517

PDF Views: 17




  • Microstructure, Mechanical and Corrosion Behaviour of AA7075 Aluminium Alloy Friction Stir Welds

Abstract Views: 517  |  PDF Views: 17

Authors

P. Vijaya Kumar
Department of Mechanical Engineering, Raghu Institute of Technology, Visakhapatnam, India
G. Madhusudhan Reddy
Defence Metallurgical Research Laboratory, Hyderabad, India
G. Madhusudhan Reddy
Defence Metallurgical Research Laboratory, Hyderabad, India
K. Srinivasa Rao
Department of Metallurgical Engineering, Andhra University, Visakhapatnam, India
K. Srinivasa Rao
Department of Metallurgical Engineering, Andhra University, Visakhapatnam, India

Abstract


Friction stir welding (FSW) is emerging as an alternative technique for joining high strength aluminium alloys as it eliminates the problems during fusion welding. In this work, the effect of post weld treatments (PWHT), viz., peak aging (T6) and retrogression and reaging (RRA) on the microstructure, mechanical properties, pitting corrosion and stress corrosion cracking (SCC) resistance of AA7075 aluminium alloy friction stir welds has been studied. An attempt also has been made to change the chemical composition of the weld nugget by adding boron carbide (B4C) nano powder with the aid of the FSW. Hardness and tensile properties were found to be better in PWHT – T6. Pitting corrosion and SCC resistances were improved in PWHT-RRA condition with negligible loss of strength when compared to PWHT-T6. RRA promotes coarse precipitation of the equilibrium phase η in the grains and sub grain boundaries, while maintaining a fine distribution of η' in the grain interiors. The increased strength and hardness in the peak aged (T6) condition was attributed to the presence of semi-coherent intermediate η' (MgZn2). With the addition of B4C nano powder to the weld nugget, hardness, tensile properties, pitting corrosion resistance and SCC resistance were further improved significantly when compared to the unreinforced weld nugget. PWHT-RRA treatment on the welds with B4C nano powder addition resulted in improved hardness of weld nugget which is attributed to the uniform distribution of strengthening precipitates in the matrix and powder strengthening. Pitting corrosion resistance, Tensile strength and SCC resistance was improved significantly in B4C added welds after RRA treatment when compared to the same welds without B4C addition.

Keywords


Friction Stir Welding, FSW, AA7075 Aluminium Alloy, Pitting Corrosion, Stress Corrosion Cracking, Retrogression-Reaging, RRA, Boron Carbide (B4C).

References





DOI: https://doi.org/10.22486/iwj%2F2018%2Fv51%2Fi2%2F170312