Indian Welding Journal

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Finite Element Based Transient Heat Transfer Analysis of Ti2AlNb Electron Beam Welds Using Hybrid Volumetric Heat Source


Affiliations
1 Department of Mechanical Engineering, North Eastern Regional Institute of Science and Technology, Nirjuli 791109, Arunachal Pradesh, India
     

   Subscribe/Renew Journal


Titanium based alloy Ti2AlNb is considered as a formidable structural material for advanced aero-engine applications due to its low density and high melting point temperature. Moreover, titanium based Ti2AlNb alloy is reactive towards atmospheric elements at an elevated temperature and hence conventional welding techniques do not fit to weld this type of materials. Furthermore, electron beam (EB) welding process is preferable to join Ti2AlNb alloy as it provides vacuum environment and possess high energy density with relatively minimum thermal input. EB welding produces deep and narrow penetration welds which leads to minimum weld induced stresses and distortion. In the recent past, several experimental analysis have been presented to comprehend the weld pool geometry during fusion welding procedures. Moreover, the phenomenological occurrence within and vicinity of the molten weld zone are primary focus of analysis. Therefore, a three-dimensional (3D) numerical model is paramount to interpret the physical occurrence of welding operation using a suitable volumetric heat source model. Nevertheless, in the current investigation, a transient heat transfer model based on finite element (FE) method is developed to simulate electron beam welds of titanium based Ti2AlNb alloy. In the course of modeling, a suitable thermal model is selected based on weldment profile and is quite accountable for determining accuracy of heat transfer analysis. The authors have considered a composite heat source model, comprising of two dimensional Gaussian distributed double ellipsoidal heat source at the top section and volumetric conical heat source through thickness of the cross section. Along with composite heat source model; material properties and latent heat of fusion as a function of temperature have been incorporated during modeling. The developed numerical heat transfer process model predicts the time-temperature history, cooling rates, weld bead dimensions and shapes. To verify the effectiveness of developed process model, the computed results are evaluated with experimentally estimated weld bead dimensions and profile. The numerical results indicated that the weld geometry characteristics and thermal history are in good accordance with the experimental data with less than 6% error. Moreover, the computed FE model results lays foundation for the estimation of welding induced distortion and residual stresses further.


Keywords

Ti2AlNb Alloy, Electron Beam Welding, FEM, Thermal Analysis, Composite Heat Source.
User
Subscription Login to verify subscription
Notifications
Font Size

  • Rai R, Palmer TA, Elmer JW and Debroy T (2009); Heat transfer and fluid flow during electron beam welding of 304L stainless steel alloy, Weld. J., 8, pp. 54s-61s.

  • Huang B, Chen X, Pang S and Hu R (2017); A threedimensional model of coupling dynamics of keyhole and weld pool during electron beam welding, Int. J. Heat Mass Transf., 115, pp. 159-173.

  • Chen X, Xie FQ, Ma TJ, Li WY and Wu XQ (2016); Effects of post-weld heat treatment on microstructure and mechanical properties of linear friction welded Ti2AlNb alloy, Mater. Des., 94, pp.45-53.

  • Chen X, Xie FQ, Ma TJ, Li WY and Wu XQ (2016); Microstructural evolution and mechanical properties of linear friction welded Ti2AlNb joint during solution and aging treatment, Mater. Sci. Eng. A, 668, pp.125-136.

  • Zhang K, Ni L, Lei Z, Chen Y and Hu X (2016); Microstructure and tensile properties of laser welded dissimilar Ti-22Al-27Nb and TA15 joints, Int. J. Adv. Manuf. Technol., pp.1-8.

  • Lei Z, Dong Z, Chen Y, Zhang J and Zhu R (2013); Microstructure and tensile properties of laser beam welded Ti-22Al-27Nb alloys, Mater. Des., 46, pp.151156.

  • Lei ZL, Dong ZJ, Chen YB, Huang L and Zhu RC (2013); Microstructure and mechanical properties of laser welded Ti-22Al-27Nb/TC4 dissimilar alloys, Mater. Sci. Eng. A, 559, pp. 909-916.

  • Tan LJ, Yao ZK, Ning YQ and Guo HZ (2011); Effect of isothermal deformation on micro-structure and properties of electron beam welded joint of Ti2AlNb/TC11, Mater. Sci. Technol., 27 (9), pp.14691474.

  • Tan LJ, Yao ZK, Wang T and Guo HZ (2011); Effect of post-weld heat treatment on micro-structure and properties of electron beam welded joint of Ti2AlNb/TC11, Mater. Sci. Technol., 27 (8), pp.13151320.

  • Li Y, Zhao Y, Li Q, Wu A, Zhu R and Wang G (2017); Effects of welding condition on weld shape and distortion in electron beam welded Ti2AlNb alloy joints, Mater. Des., 114, pp. 226-233.

  • Yadaiah N, Bag S, Paul CP and Kukreja LM (2015); Fiber laser welding in a controlled inert gas atmosphere: An experimental and numerical investigation, in Laser Based Manufacturing, Springer, Chapter 20, pp.399-419.

  • Yadaiah N, Bag S, Paul CP and Kukreja LM (2016); Influence of self-protective atmosphere in fiber laser welding of austenitic stainlesssteel, Int. J. Adv. Manuf. Technol., 86(1), pp. 853-870.

  • Yadaiah N and Bag S (2014); Development of eggconfiguration heat source model in numerical simulation of autogenous fusion welding process, Int. J. Ther. Sci., 86, pp. 125-138.

  • Yadaiah N and Bag S (2013); Role of Oxygen as SurfaceActive Element in Linear GTA Welding Process, J. Mater. Eng. Perfor., 22(11), pp. 3199-3209.

  • Yadaiah N and Bag S (2012); Effect of heat source parameters in thermal and mechanical analysis of linear GTA welding process, ISIJ Int., 52(11), pp. 2069-2075.

  • Luo Y, You G, Ye H and Liu J (2010); Simulation on welding thermal effect of AZ61 magnesium alloy based on three-dimensional modeling of vacuum electron beam welding heat source, Vacuum, 84,pp. 890–895.

  • Chiumentia M, Cervera M, Dialami N, Wu B, JinweiL and Saracibar CA (2016); Numerical modeling of the electron beam welding and its experimental validation, Finite Elem. Anal. Des., 121, pp.118–133.

  • Lacki P and Adamus K (2011); Numerical simulation of the electron beam welding process, Comput. Struct., 89, pp. 977–985.

  • Lacki P, Adamus K and Wieczorek P (2014); Theoretical and experimental analysis of thermo-mechanical phenomena during electron beam welding process, Comput. Mater. Sci., 94, pp. 17-26.

  • Bardel D, Neliasa D, Robin V, Pirling T, Boulnat X and Perez M (2016); Residual stresses induced by electron beam welding in a 6061 aluminium alloy, J. Mater. Process. Technol., 235, pp.1-12.


Abstract Views: 492

PDF Views: 7




  • Finite Element Based Transient Heat Transfer Analysis of Ti2AlNb Electron Beam Welds Using Hybrid Volumetric Heat Source

Abstract Views: 492  |  PDF Views: 7

Authors

Sohini Chowdhury
Department of Mechanical Engineering, North Eastern Regional Institute of Science and Technology, Nirjuli 791109, Arunachal Pradesh, India
Yadaiah Nirsanametla
Department of Mechanical Engineering, North Eastern Regional Institute of Science and Technology, Nirjuli 791109, Arunachal Pradesh, India
Manapuram Muralidhar
Department of Mechanical Engineering, North Eastern Regional Institute of Science and Technology, Nirjuli 791109, Arunachal Pradesh, India

Abstract


Titanium based alloy Ti2AlNb is considered as a formidable structural material for advanced aero-engine applications due to its low density and high melting point temperature. Moreover, titanium based Ti2AlNb alloy is reactive towards atmospheric elements at an elevated temperature and hence conventional welding techniques do not fit to weld this type of materials. Furthermore, electron beam (EB) welding process is preferable to join Ti2AlNb alloy as it provides vacuum environment and possess high energy density with relatively minimum thermal input. EB welding produces deep and narrow penetration welds which leads to minimum weld induced stresses and distortion. In the recent past, several experimental analysis have been presented to comprehend the weld pool geometry during fusion welding procedures. Moreover, the phenomenological occurrence within and vicinity of the molten weld zone are primary focus of analysis. Therefore, a three-dimensional (3D) numerical model is paramount to interpret the physical occurrence of welding operation using a suitable volumetric heat source model. Nevertheless, in the current investigation, a transient heat transfer model based on finite element (FE) method is developed to simulate electron beam welds of titanium based Ti2AlNb alloy. In the course of modeling, a suitable thermal model is selected based on weldment profile and is quite accountable for determining accuracy of heat transfer analysis. The authors have considered a composite heat source model, comprising of two dimensional Gaussian distributed double ellipsoidal heat source at the top section and volumetric conical heat source through thickness of the cross section. Along with composite heat source model; material properties and latent heat of fusion as a function of temperature have been incorporated during modeling. The developed numerical heat transfer process model predicts the time-temperature history, cooling rates, weld bead dimensions and shapes. To verify the effectiveness of developed process model, the computed results are evaluated with experimentally estimated weld bead dimensions and profile. The numerical results indicated that the weld geometry characteristics and thermal history are in good accordance with the experimental data with less than 6% error. Moreover, the computed FE model results lays foundation for the estimation of welding induced distortion and residual stresses further.


Keywords


Ti2AlNb Alloy, Electron Beam Welding, FEM, Thermal Analysis, Composite Heat Source.

References





DOI: https://doi.org/10.22486/iwj%2F2019%2Fv52%2Fi1%2F178190