Indian Welding Journal

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Thermal Assisted Friction Stir Welding of HSLA Steel:A Novel Approach to Mitigate Lower Toughness and Ductility


Affiliations
1 Naval Metallurgy Division, Naval Materials Research Laboratory, Ambernath, Thane-421506, Maharasthra, India
2 Defence Institute of Advanced Technology, Girinagar, Pune-411205, India
     

   Subscribe/Renew Journal


Friction stir welding (FSW) technology is well-known forits capability to join low softening metals and alloys such as aluminum and magnesium, conversely, high softening alloys like steel, titanium and nickel alloys is still a challenge due to tool material stringent property requirements and its availability. Presently, with the advancement in the development of tool materials,the joining of high softening alloysis possible. However, in case of high strength quench sensitive grade of steel, high cooling rate associated during FSW induces undesirable brittle martensitic microstructure and therefore, reduces the properties of the weld zone, particularly, the ductility and toughness. Therefore, in present investigation a novel approach to control the microstructure was investigated by employing induction pre heating source ahead of tool pin during FSW. The HSLA plate preheated at 300 °C and 600 °C respectively resulted in simultaneous increase of ductility and toughness because of widmanstätten ferrite and bainitic microstructure due to lower cooling rate. In case of FSW carried out without preheating the hard brittle zone was found, whereas the same was eliminated with preheating source. Optical and scanning electron microscope (SEM) with electron back scattered diffraction (EBSD) detector was utilized to characterize the microstructure of FSW nugget zone, and was correlated with mechanical properties.

Keywords

Thermal Assisted Friction Stir Welding, High Strength Low Alloy Steel (HSLA), Microstructure, Mechanical Properties, Scanning Electron Microscopy.
User
Subscription Login to verify subscription
Notifications
Font Size

  • Zhang L and Kannengiesser T (2014); Austenite grain growth and microstructure control in simulated heat affected zones of microalloyed HSLA steel, Mater. Sci. Eng. A, 613, pp. 326-335.

  • McNelley TR, Swaminathan S and Su JQ (2008); Recrystallization mechanisms during friction stir welding and processing on aluminium alloy, Scr. Mater., 58, pp. 349-354.

  • Cam G (2011); Friction stir welded structural materials: beyond Al-alloys, Int. Mater. Review, 56, pp. 1-48.

  • Sampath K (2006); An understanding of HSLA-65 plate steels, J. Mater. Eng. Perform. 15, pp. 32–40.

  • Liu Y, Shi L, Liu C, Yu L, Yan Z and Li H (2016); Effect of step quenching on microstructures and mechanical properties of HSLA steel, Mater. Sci. Eng. A, 675, pp. 371–378.

  • Wei L and Nelson TW (2012); Influence of heat input on the post weld microstructure and mechanical properties of friction stir welded HSLA-65 steel, Mat.Sci. Eng. A, 556, pp. 51-59.

  • Wei L and Nelson TW (2011); Correlation of Microstructures and Process Variables in FSW HSLA-65 Steel, Welding J., 90, pp. 95s-101s.

  • Ragu Nathan S, Malarvizhi S, Balasubramanian V and Rao AG (2016), Failure analysis of tungsten based tool materials used in friction stir welding of high strength low alloy steels, Eng. Fail. Ana,18, pp. 18-36.


Abstract Views: 326

PDF Views: 7




  • Thermal Assisted Friction Stir Welding of HSLA Steel:A Novel Approach to Mitigate Lower Toughness and Ductility

Abstract Views: 326  |  PDF Views: 7

Authors

B.D. Bhanushali
Naval Metallurgy Division, Naval Materials Research Laboratory, Ambernath, Thane-421506, Maharasthra, India
A. GouravRao
Naval Metallurgy Division, Naval Materials Research Laboratory, Ambernath, Thane-421506, Maharasthra, India
A. P. Singh
Naval Metallurgy Division, Naval Materials Research Laboratory, Ambernath, Thane-421506, Maharasthra, India
S. Parida
Naval Metallurgy Division, Naval Materials Research Laboratory, Ambernath, Thane-421506, Maharasthra, India
V. P. Deshmukh
Naval Metallurgy Division, Naval Materials Research Laboratory, Ambernath, Thane-421506, Maharasthra, India
A. C. Abhayankar
Defence Institute of Advanced Technology, Girinagar, Pune-411205, India
T. Shanmugasundaram
Defence Institute of Advanced Technology, Girinagar, Pune-411205, India

Abstract


Friction stir welding (FSW) technology is well-known forits capability to join low softening metals and alloys such as aluminum and magnesium, conversely, high softening alloys like steel, titanium and nickel alloys is still a challenge due to tool material stringent property requirements and its availability. Presently, with the advancement in the development of tool materials,the joining of high softening alloysis possible. However, in case of high strength quench sensitive grade of steel, high cooling rate associated during FSW induces undesirable brittle martensitic microstructure and therefore, reduces the properties of the weld zone, particularly, the ductility and toughness. Therefore, in present investigation a novel approach to control the microstructure was investigated by employing induction pre heating source ahead of tool pin during FSW. The HSLA plate preheated at 300 °C and 600 °C respectively resulted in simultaneous increase of ductility and toughness because of widmanstätten ferrite and bainitic microstructure due to lower cooling rate. In case of FSW carried out without preheating the hard brittle zone was found, whereas the same was eliminated with preheating source. Optical and scanning electron microscope (SEM) with electron back scattered diffraction (EBSD) detector was utilized to characterize the microstructure of FSW nugget zone, and was correlated with mechanical properties.

Keywords


Thermal Assisted Friction Stir Welding, High Strength Low Alloy Steel (HSLA), Microstructure, Mechanical Properties, Scanning Electron Microscopy.

References





DOI: https://doi.org/10.22486/iwj%2F2019%2Fv52%2Fi4%2F186787