Manufacturing Technology Today

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Quality Improvement Through Optimization of Parameters of Honing Process


Affiliations
1 K.I.T.’s College of Engineering, Kolhapur, Maharashtra, India
2 Department of Technology, Shivaji University, Kolhapur, Maharashtra, India
     

   Subscribe/Renew Journal


The surface quality of any cylinder bores with improved sliding properties is often produced by the honing process. This multi-stage process is performed using abrasive tools fed against the bore with simultaneous rotary and oscillatory motion. To have process robustness with acceptable dimensional accuracy and surface quality, the various process parameters have to be studied deeply. This paper aims to improve the quality of honing process by optimizing and analyzing the cylinder liner surface roughness which is influenced by various process parameters during honing. Conducting the experimental runs according to the design of experiment and analyzing the results which are finally validated through confirmation experimentation.

Keywords

Honing, Design of Experiment, Analysis of Variance (ANOVA), S/N Ratio, Response Surface Method.
User
Subscription Login to verify subscription
Notifications
Font Size

  • Misra, JP; Jain, PK; Dwivedi, DK: Electrochemical honing-A novel technique for gear finishing, DAAAM International Scientific book Chapter 29, 2011, 365-382.

  • Vrac, Damir S; Sidjanin, Leposava P; Kovac, Pavel P; Balos, Sebastian S: The influence of honing process parameters on surface quality, productivity, cutting angle and coefficients of friction, Industrial Lubrication and Tribology, 2012, vol. 64, no. 2, 77-83.

  • Goeldel, Benoit; Mansori, Mohamed EL; Didier Dumur: Macroscopic simulation of the liner Honing process, 'CIRP Annals', Manufacturing Technology, 2012, vol. 61, no. 1, 319-322.

  • Harpreet Singh and Pramod Kumar Jain: Comparative Study on ECH of Spur Gears under Direct and Pulse Current, 'Int. J. Mech. Eng. Autom'., vol. 2, no. 4, 2015, 183-187 Received: January 18, 2015; Published: April 25, 2015

  • Aniket Kishor Deshpande; Harshal Anil Bhole; Laxman Ashok Choudhari: Analysis of Super-Finishing Honing Operation with Old and New Plateau Honing Machine Concept, 'International Journal of Engineering Research and General Science', vol. 3, no. 2, Part 2, March-April, 2015, ISSN 2091-2730

  • Pimpalgaonkar, MH; Guge Ranjesh Laxmanrao; Ade Santosh Laxmanrao: A review of optimization process parameters on honing machine, 'International Journal of Mechanical and Production Engineering', ISSN: 2320-2092, vol. 1, no. 5, Nov-2013


Abstract Views: 263

PDF Views: 0




  • Quality Improvement Through Optimization of Parameters of Honing Process

Abstract Views: 263  |  PDF Views: 0

Authors

Vaibhav S. Kengar
K.I.T.’s College of Engineering, Kolhapur, Maharashtra, India
Jaydeep S. Bagi
Department of Technology, Shivaji University, Kolhapur, Maharashtra, India

Abstract


The surface quality of any cylinder bores with improved sliding properties is often produced by the honing process. This multi-stage process is performed using abrasive tools fed against the bore with simultaneous rotary and oscillatory motion. To have process robustness with acceptable dimensional accuracy and surface quality, the various process parameters have to be studied deeply. This paper aims to improve the quality of honing process by optimizing and analyzing the cylinder liner surface roughness which is influenced by various process parameters during honing. Conducting the experimental runs according to the design of experiment and analyzing the results which are finally validated through confirmation experimentation.

Keywords


Honing, Design of Experiment, Analysis of Variance (ANOVA), S/N Ratio, Response Surface Method.

References