Table of Contents
Vol 18, No SP 3 (2019)
Open Access
Subscription Access
Journey of (CMTI)
Journey of Central Manufacturing Technology Institute (CMTI) | ||
Vol 18, No SP 3 (2019), Pagination: 2-3 | ||
ABSTRACT | PDF | Abstract Views: 257 | PDF Views: 0 |
Technical Paper
Design of Special Fixture for Hard Chromium Plating on Internal Surface of Hollow Cylinder Open at One End and with Restricted Opening at the Other End with L/D Ratio More than 4 | ||
S. S. Avadhani, Champuri Srinivas Rao, C. J. Kumara | ||
Vol 18, No SP 3 (2019), Pagination: 4-9 | ||
ABSTRACT | PDF | Abstract Views: 308 | PDF Views: 0 |
Review on Design Guidelines for Selective Laser Melting | ||
B. N. Manjunath, Prafullakumar Chaudhari, Hemant Pawar, S. K. Verma, S. S. Anasane | ||
Vol 18, No SP 3 (2019), Pagination: 10-18 | ||
ABSTRACT | PDF | Abstract Views: 300 | PDF Views: 0 |
Calibration of Co-Ordinate Measuring Machine by Self Tracking Laser Interferometer (Laser Tracer) | ||
H. S. Chethan, P. Rama Mohan, C. T. Shivaraju | ||
Vol 18, No SP 3 (2019), Pagination: 19-24 | ||
ABSTRACT | PDF | Abstract Views: 269 | PDF Views: 0 |
Investigation on the Effect of Nucleation Time on CNT Growth Process using RF-PECVD | ||
K. Ankit, K. Niranjan Reddy, Gokul, N. Balashanmugam | ||
Vol 18, No SP 3 (2019), Pagination: 25-30 | ||
ABSTRACT | PDF | Abstract Views: 232 | PDF Views: 0 |
Piezo-Resistive Mems Pressure Sensor for Tire Bead Seating Pressure Measurement:Design, Simulation, Analysis and Fabrication Process | ||
N. Kusuma, E. S. Sujit | ||
Vol 18, No SP 3 (2019), Pagination: 31-38 | ||
ABSTRACT | PDF | Abstract Views: 255 | PDF Views: 0 |
Mechanical and Structural Characterization of DLC Prepared by PECVD Technique | ||
Champuri Srinivas Rao, Leo Prakash | ||
Vol 18, No SP 3 (2019), Pagination: 39-41 | ||
ABSTRACT | PDF | Abstract Views: 232 | PDF Views: 0 |
Study on the Influence of Spindle Running Accuracy and Feed Drive Characteristics of a Diamond Turning Machine on Work Piece Accuracy | ||
Prakash Vinod | ||
Vol 18, No SP 3 (2019), Pagination: 42-46 | ||
ABSTRACT | PDF | Abstract Views: 218 | PDF Views: 0 |
Mathematical Modeling of Spindle Deflection for Multi Spindle Automat and Validation using Ansys Software | ||
G. S. Pramod Krishna, Tom Saju | ||
Vol 18, No SP 3 (2019), Pagination: 47-53 | ||
ABSTRACT | PDF | Abstract Views: 287 | PDF Views: 0 |
Challenges and Research Opportunities in Metal Additive Manufacturing | ||
B. N. Manjunath, A. R. Vinod, S. K. Verma, N. Balashanmugam | ||
Vol 18, No SP 3 (2019), Pagination: 54-57 | ||
ABSTRACT | PDF | Abstract Views: 265 | PDF Views: 0 |
Effect of Excimer Laser Parameters on the Ablation Depth During Micromachining of Polycarbonate | ||
E. Pradeep Kumar Reddy, Sunil Magadum | ||
Vol 18, No SP 3 (2019), Pagination: 58-61 | ||
ABSTRACT | PDF | Abstract Views: 226 | PDF Views: 0 |
Functional Evaluation of Copper in Conventional Wire Bonding as Compared to Gold | ||
S. Harsha, S. Mahalakshmi, Alexander George | ||
Vol 18, No SP 3 (2019), Pagination: 62-67 | ||
ABSTRACT | PDF | Abstract Views: 266 | PDF Views: 0 |